Search results

  1. devildog88

    temp sensor/switch

    Okay guy i have a question which sensor controls the engine light and which sensor controls the timing advance and the high idle? If I remember right the one near the fuel filter is controls the timing advance and the one in the head controls the temp light, am I right here or backwards?:dunno
  2. devildog88

    Glow plug harness

    Does anyone know where I can get a new glow plug harness, can i still get one threw ford? The ends that plug on to the glow plugs are falling off and i don't think i am getting voltage to two of the plugs.
  3. devildog88

    filler neck

    okay guys putting fuel in to my truck is always a real pain in the rear. I have to hold the lever on the pump most of the time and just trickle it in the tank. I just checked and the vent is not pluged and there dont seem to be any kinks in the lines. Has anyone modafied there filler necks to...
  4. devildog88

    dana 60 swap

    okay fellas i just found a 60 front axle for my truck. The guy said is from the 90's and is high pinon and has king pins. Will i need a different drive shaft then the one that is on my truck know? Also does anyone know where i can get a track bar mount, the guy doesnt hve on. Is there...
  5. devildog88

    turbo

    anyone have a turbo kit that they are looking to sell. i am really in need of one and havnt seen any on ebay in a while. If you do let me know thanks guys
  6. devildog88

    door panels/ dash board

    Is there a sorce for replacement door panels for a 1993? i looked thru lmc trucks catalog and only seen them ford the 80's to 91 nothing for 93 and up? Also does anyone know if i can still get the piece from ford to fix the dash board sag on the pass side.
  7. devildog88

    turbo

    well i was just wondering if anyone has a turbo that they are selling. I have finally saved up enough money and with the price of fuel i need to increase my milage any way i can:D so if anyone has one for sale let me know thanks guys
  8. devildog88

    nj superduty cummins conversion

    http://cgi.ebay.com/ebaymotors/1994-ford-superduty-Cummins-Diesel-conversion-Parts-5-9_W0QQitemZ330220755276QQcmdZViewItem?hash=item330220755276 i think i may have to go look at this;Sweet
  9. devildog88

    may have found myself a dana 60

    okay i think i have located a dana 60 and sterling 10.025" out of a 88 350 for 600$ is this a good deal? The axles have 4.10 gears and my truck has 3.55. I have a few questions do i need the panard bar to install the axle in my truck. also can i use my ring and pinion from my dana 50 in the...
  10. devildog88

    Locking hubs

    i have a question about buying a new set of locking hubs. Right now i have a dana d50 up front but i am always on the look out for a dana 60. I always thought that then dana 50 and 60 used the same locking hubs, but some of the parts places list the dana 50 as having 30 splines and the dana 60...
  11. devildog88

    rocker arms

    i pulled the drivers side valve cover and i found a really lose rocker arm the bolt was tight push rod straight and the valve dosent feel lose. can this be the sorce of my horrible idle problem?
  12. devildog88

    running ruff with smoke

    on my way home the truck started to run extremly ruff and it begain to smoke i dont know if this is because its getting could or not? well it idles horribly but if you give it some throttle it will clear up but run very ruff in a few seconds. I cracked open all of the injector lines and the all...
  13. devildog88

    buying a turbo

    well i think i have finally have the money for a turbo. i think i am going to go for a new one. My question is does anyone know if ats is selling there turbo kits now i know that they stopped for a while? IF not i guess that the only other option is hypermax. How are there kits compared to ats?
  14. devildog88

    power steering pulley removal

    how do you remove the pulley from the pump? is it pressed on or threaded?
  15. devildog88

    Blowby

    how much white smoke should i see when i remove the oil filler cap after the motor has been run and gotten to operating temp?
  16. devildog88

    wheel bearing question

    okay so i stop off today to pick up some wheel bearings now i didnt pull them out yet i wanted to make sure they had them and i got everything i needed so the truck wasnt down for to long. well the guy at the computer said it listed 2 different ones cone or cup for both inside and out???:dunno...
  17. devildog88

    compression tester

    will this one work on our motors? does it have the adapter that i need? http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=93644
  18. devildog88

    what the hell

    well i found this thing earlyer and i am still confused:rotflmao :rotflmao :duhttp://cgi.ebay.com/ebaymotors/1987-F-350-4X4-Diesel-4-door-Custom-stepside-Auto_W0QQitemZ230177013859QQihZ013QQcategoryZ39416QQssPageNameZWDVWQQrdZ1QQcmdZViewItem
  19. devildog88

    stearing box leaking

    okay my steering box has developed a leak at the bottom where the pitman arm goes. how do i remove the gear box to replace the seal and how hard is it to repalce the seal. i really need the truck and do really have the money right know to replace the whole box or i would. :mad:
  20. devildog88

    brake lines

    does any one sell a prebent brake line kit i need something quick and simple to install. i would like stainless steel if possible;Sweet
  21. devildog88

    which oil would you run

    okay i have three to choose from moble 1 delvac delro shell rotala t all priced about the same which would you run?
  22. devildog88

    why does my truck eat belts

    okay since i have been driving this truck (about a year) i have had to replace the belt three or four times. last time i put a new tensioner on and evidiently that didnt do anything cause it happened again today.what should i look for? this is really starting to get old:mad: :mad: -cuss :mad...
  23. devildog88

    shift kit e4od

    who makes the best shift kit for the e4od. and how hard are they to put in? thanks guys
  24. devildog88

    transmission wire harness

    can i get a replacement wire harness for my e4od i just replaced the tps sensor and i swaped pcms i would like to make sure that my trans problems are not eletrical then going and spending thousands on replacing the trans thanks guys
  25. devildog88

    best sorce for replacemetn e40d

    hi guys this board is great lots of help and it looks like you guys have alot of fun. i have a 93 n/a idi 4x4 e4od. it looks like my trans is shot and it needs to be replaced. :mad: but i cant complain its got 175k on it never been replaced before just fluid and filter changes. well i dont...

Latest posts

Forum statistics

Threads
91,299
Posts
1,129,936
Members
24,109
Latest member
Lance

Members online

Total: 718 (members: 12, guests: 706)

Share this page

Top