So what did you do with your truck today?

[Dane Rickford]

Well, today my flat bed officially became part of my 350. I had an extra fender emblem so it got slapped on the flatbed

 

[Dane Rickford]

You must be registered for see images attach

You must be registered for see images attach

 

[Exhumis]

Let's see. Reinstalled inner fenders liner, reinstalled a clamp that fell off(wondered what that new noise was), new passenger bank return lines, cleaned up engine bay wiring(loomed and taped)

 

[WAID]

Put in new front shocks, glow plugs, and returned lines. Even washed all the dirt off the truck and camper. Too bad I don't know when I'll get to take it out again, but have a trip down to california planned for later this year.

 

[lsaami]

Tightened my front right wheel bearing (had some play, but plenty of grease and no grinding) and pulled a rock out of the dust shield.

I also replaced a few clips in my door panel, and added some Lucas oil additive.

 

[jericho]

Yesterday got my new IP from Conestoga installed with new return lines. Both were original to the truck. Static timed only but it runs great what power! Today removed front rusted out front bumper. Got a replacement cheap on eBay I'll put on tomorrow if it doesn't rain too much. Was gonna travel long distance soon, before all the state's around me shutting down, truck stops, food etc. aren't dependable right now.

You must be registered for see images attach

I used 1/2 inch copper pipe polished up so no burrs to slip the new o-rings over the sharp threads of the injectors. Worked great.

You must be registered for see images attach

the cover on the right looked exactly like the one on the left the day before. I just used my steel brush wheel, high build primer, then metallic paint. Then silicone glued the label back on. That paint really looks like polished aluminum. They are both done now and the truck looks a lot better.

You must be registered for see images attach

 

[rhythim]

No more guessing games on how much fuel is in the tanks.

You must be registered for see images attach

Sent from my SM-G975U using Tapatalk

 

[ABNORDY]

Replaced the ignition switch. No more stalls and don't have to jiggle the key to make the radio work anymore.

You must be registered for see images attach

Sent from my SM-N950U using Tapatalk

 

[Dane Rickford]

Today I changed my tranny fluid, and while I was under the truck I kept glancing at the exhaust and was thinking about the terrible stock down pipe, sooooo, I decided to to bite the bullet and build a 3 in dp. Went hunting in the scrap pile and found some pipe, and began cutting. I got everything cut and bent, tomorrow I hope to get it welded and slap it on.

 

[IDIBRONCO]

Be sure to let us know how it turns out. With pictures. We're a lot like little kids, we like looking at the pictures.

 

[Dane Rickford]

I definitely will let you all know how it turns out. And I am still a kid, and I like pictures too
Here is what it looks like right now:

You must be registered for see images attach

 

[Dane Rickford]

Whoops, that picture uploaded upside down

 

[Dane Rickford]

Ok, I got excited and couldn’t resist and got the dp all tacked together it fits perfect and slides right in even though it’s a full 3 inch

You must be registered for see images attach

You must be registered for see images attach

 

[Laine D]

Ok, I got excited and couldn’t resist and got the dp all tacked together it fits perfect and slides right in even though it’s a full 3 inch

You must be registered for see images attach

You must be registered for see images attach

I’m 99% sure I spoke to you about buying your old block. Then I had to get a new phone and couldn’t find the add on Craigslist after that lol.

 

[Laine D]

Today I got my 38 gallon tank painted up and ready to install. Hoping to pick up an Intercooler this weekend as well.

You must be registered for see images attach

You must be registered for see images attach