Recent content by Twostacks
-
Slave Cylinder Installation
No, I meant "Ratchet Clamp", got a throw away from Harbor Freight . Took the pads off and drilled a dimple on the edge so that the round end of the push rod would sit in it , mounted the slave and used a screw driver to pluck it into place. Clamp down on the slave before mounting. used a fifteen...- Twostacks
- Post #9
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Slave Cylinder Installation
Had the same issue, used a ratchet clamp to squeeze the push rod in, worked like a charm- Twostacks
- Post #4
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Diesel Injection Service based out of Mobile, AL.
Anybody ever use "Diesel Injection Service" located in Mobile, AL for pumps or rebuild service- Twostacks
- Thread
- Replies: 4
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Which Flywheel
Thanks for your reply icanfixall, but which one should I buy as far as tooth count or does it matter. I found some with 155 and 157 mine is 154 and I'm not sure that's the right one.- Twostacks
- Post #3
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Which Flywheel
I have a 94 F250 7.3 IDI Turbo with 5 spd that I converted from DMF to SMF. I have about 4k miles on it since the conversion and the starter started to grind against the flywheel teeth on the flywheel, thinking it was a bad starter I replaced it and it did not resolve the grinding issue. I...- Twostacks
- Thread
- Replies: 2
- Forum: 6.9L IH & 7.3L IDI Diesels
-
BABY MOOSE FOR SALE
****SOLD***** SOLD***Before I sell my truck I removed the baby moose pump I had rebuilt by Mel and replaced it with my spare stock one. I hate to sell it but it gets very little use. The pump is about 2 years old and has about 5K miles on it. It ran on a clean fuel system and by that I mean I...- Twostacks
- Thread
- Replies: 4
- Forum: Marketplace
-
Help broke off a screw on my locking hub
yes I tried but it snapped about 1/4" below the surface of the hub making it difficult to center punch. I went to carquest and ordered a set of Mile Markers should have them on Monday. Thanks- Twostacks
- Post #5
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Help broke off a screw on my locking hub
I guess I didn't make myself clear, It not the allen screw I need it's the locking hub where the screw goes in to hold the hub cover with the selector. Anyone that would post to buy a 5 cent allen screw should drive thier truck to the nearest junk yard and have it crushed. Anyway went to my...- Twostacks
- Post #3
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Help broke off a screw on my locking hub
Just put new bearings and universals on my frontend and snap :***: one of the screws that hold the locking cap on. Does anyone have a spare locking hub they want to sell? It's for a 94 f250 D50 30 spline. I can paypal. Thanks V- Twostacks
- Thread
- Replies: 14
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Kent Moore Timing Meter On Ebay
Hey Gary I got your Kent Moore delivered on Monday. I'll be timing my truck this Saturday and will be ready to ship to the next member on Monday. I'm thinking of turning up the pump a flat or two and was wondering if this would effect the timing. Should I time it first then turn it up or vice...- Twostacks
- Post #5
- Forum: 6.9L IH & 7.3L IDI Diesels
-
I'll never let anyone drive my truck
This weekend took my boat out for a nice day of fishing. My brother caught a nice 24" fluke which is very rare in the waters off New Jersey, anyway after about 5 hours we headed back to the ramp and anything that could go wrong went wrong:mad:. First we broke the negative stud on the battery...- Twostacks
- Thread
- Replies: 54
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Gremlins are here, troubleshooting help please.
I sure hope not, :angel: when I installed mine I didn't take the clocking of the lifter in the bore into consideration. engine runs fine and I was getting plenty of oil to the rockers- Twostacks
- Post #36
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Had to replace a battery today. Bought a group 31......
x2:sly- Twostacks
- Post #14
- Forum: 6.9L IH & 7.3L IDI Diesels
-
To Moose or not to Moose that is my question
I just took mine to MV inspection about a month ago and found out that any diesels pickups older then 1996 are exempt from emissions testing in Jersey no inspection sticker issued, but like Goose mention the State troopers and local cops can and will inspect your rig if they deem nescessary. If...- Twostacks
- Post #42
- Forum: 6.9L IH & 7.3L IDI Diesels
-
To Moose or not to Moose that is my question
Not rich by any means :rotflmao I work for the State of NJ and Governor Christie just took a big ass bite out of my check. If I had the money I'd be driving a new Ford diesel :D I don't need to roll the coal cops don't like it much in these parts of Jersey, but I hear what your saying.- Twostacks
- Post #12
- Forum: 6.9L IH & 7.3L IDI Diesels
