Search results

  1. stumiister

    Fault codes

    Im working with 2006 F450 cab and chassis it has the POS 6.0 in it and now its a gutless POS it inlimp mode barley does 65 on the freeway I got some codes and i want to know what needs to be reomved inspected and or replaced the codes are as follows: P0299 Turbo under boost P1408 EGR Valve out...
  2. stumiister

    Glow Plugs Not Working

    This morning like Saturday morning since its been a bit cold here it took over an hour to get the engine to finally start and stay running, no check engine light, ether didn't help either, the glow plug light cycles properly but I just don't know if they are working or if its a fuel problem...
  3. stumiister

    '86 IDI no fuel to injectors

    My buddy has a '86 IDI NA 2wd with a ZF5 I swapped the IP out for him. No I didn't remove the gear the IP I only removed the IP with the hard lines to the injectors. The lift pump pushes fuel to the IP inlet but I'm wondering why it doesn't want to start or even bleed the air out of the hard...
  4. stumiister

    I hate vicious circles

    It all started yesterday I was drving home and noticed the voltage guage in my truck was showing only 12 volts I wne t to the local O'reillys to have them check the charging system since them do it for free and I bought a altenator and regulator from them. They tested everything the regulator...
  5. stumiister

    How much R134 do I need for my '85 F250

    The underhood label is missing. I have the bosses RobinAir a/c recycler/recharger machine hooked up to the truck after everything is out and I have a good vacuum in the system when I go to recharge it how much R134 do I add?
  6. stumiister

    Cool E Model

    Found this on you tube I thought this might have an IDI in it. http://www.youtube.com/watch?v=32kK7lQZSks
  7. stumiister

    Messed up vacuum pump pulley

    I was going to replace the vacuum pump but the pulley doesnt want to come off and now im stuck. I have a old power steering pump pulley I could use. But would there be a difference in the alignment of the belt? It would be a temparory fix until i get the right pulley. Any thoughts or...
  8. stumiister

    I know this isnt the right forum, Urea in diesel fuel

    I know this isnt the right forum but I'm sure this forum will help me. Who can tell me how to remove UREA from diesel fuel? I have about 200gls of urea contaminated diesel and I'd like to use but the urea is made up of water and another corrisive chemical. Urea is badfor the fuel systeem it...
  9. stumiister

    Urea in deisel fuel

    Who knows how to remove urea from diesel fuel?
  10. stumiister

    Found this thought y'all might like it

    This is one crazy tractor https://www.facebook.com/photo.php?v=4373712255818&set=vb.128965393876812&type=2&theater
  11. stumiister

    Thermo king triPac Apu not cranking

    Im working with a tripac apu it is not cranking I checked all of the fuses in the under bunk control box Checked the engine on off switch at the engine it is on Checked the circuit breaker at the under bunck control box it is good When I turn the unit on the fuel pump comes on and I get fuel...
  12. stumiister

    7.3 heads in Ca

    Found these on CL if anyone is interested. http://stockton.craigslist.org/pts/3686102544.html
  13. stumiister

    Need torque spec for GP's and intake gasket for a Benz OM606 engine

    I will be changing the gp's and the intake gasket this weekend on my Mercedes Benz OM606 engine Who can tell me the torque for the GP's and the intake gasket? I think the GP's are 27nm. But havent found any info on the intake manifold. I have tried looking on the internet but havent found...
  14. stumiister

    Torque spec for glow plugs and intake manifold

    I will be changing the gp's and the intake gasket this weekend. Who can tell me the torque for the GP's and the intake gasket? I think the GP's are 27nm. But havent found any info on the intake manifold.
  15. stumiister

    Oil leak from drain plug

    I have an oil leak from the drain plug I replaced the drain plug when I rebuilt the engine with a magnetic drain plug I got from O'Reillys but it is leaking now. I found this on EBAY, is this the correct part number...
  16. stumiister

    Doing good

    Yesterday I realized I have put about 9K miles on my rebuilt engine and I havent had any issuses with it other than the freeze plugs popping out which hasnt happened for a while since I got the tool from OTC and I have used the avaition cement. Keeping my fingures crossed that this truck last...
  17. stumiister

    New to me

    I know this isnt the right forum but I will get more input here than anywhere else. I just purchased a new to me 1993 Mercedes Benz E 300 Diesel, not sure the engine size but it is a 6cyl na diesel with just over 200k on the clock and its not in that bad of shape for me to be the 4th owner.
  18. stumiister

    Oppertunity to buy a MB 300D non turbo

    I have a friend that wants to sell me his early to mid '90's 300D non turbo, what kind of fuel milage do you see with it ? did they come with 4spd trannies? How simple are the engines to work on?, this particular 300D has a 5 cylinder engine in it. He has told me that the GPs dont work but...
  19. stumiister

    I wonder if this has an IDI in it.

    Found this on facebook today https://www.facebook.com/#!/photo.php?fbid=480876235307409&set=a.418431401551893.94372.418420328219667&type=1&theater
  20. stumiister

    New king pins

    I ordered a set of Moog 8985b king pins for my truck, according to the Ford part number they are the same part, but boy they sure do look small compared to the king pins I install in the big trucks.
  21. stumiister

    Truck still wanders while driving

    I replaced the tie rod ends from one wheel to the other, replaced the steering coupler. What can I do to reduce the slop in the steerin the only thing left to adjust or replce is the steering gear. Any comments will help thanks.
  22. stumiister

    Help with steering torque specs

    Im replacing all the innner and outer tie rod ends and the adjusting sleeves, I tried to search for the torque specs but couldnt find any, help please and I cant go home until I finish thanks.
  23. stumiister

    Question about fuel tanks

    Ok we all know on a big truck they have dual tanks that draw and return fuel into both tanks at the same time. the tank capacity on most of these trucks are about 150 u.s. gallonsin each tank. Im curious has anyone tried to set up a truck like ours that has dual tanks that would draw and...
  24. stumiister

    Question about tie rod ends

    I have seen tie rod ends listed on ebay, jc whitney, LMC, ad Rock auto, they are all priced about the same but I wondering about brand quality, I know moog is a good brand along with reysbestos but im wondering about the lessor know brands. Any coments are welcome. Thanks.
  25. stumiister

    Im surprised

    I replaced the thermostat in my truck yesterday, the PO installed one that looks like it belonged in a small block ford or Chevy, I went to the local International dealer to get one it was a bit pricey but I needed it, I was surprised when I started the truck after I was done how much a...

Latest posts

Forum statistics

Threads
91,283
Posts
1,129,783
Members
24,099
Latest member
IDIBronco86

Members online

Total: 401 (members: 11, guests: 390)

Share this page

Top