Shadetreemechanic
Full Access Member
Why are you tucking the engine and transmission so far back?
Centurion Bronco build
- Thread starter IDIoit
- Start date
actually its more forward than stock, and a lot higher.
You must be registered for see images attach
valid message
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
had to grab a side shot too!
You must be registered for see images attach
Hood scoop??? Looking like it might need one.....
whatever happens, happens on the bumpers, thinking about a 6" tube bumper but set back to resemble a front roll pan.
most definitely a cowl hood, but the hood closes with the housing and IP.
I have big plans for that engine compartment..
most definitely a cowl hood, but the hood closes with the housing and IP.
I have big plans for that engine compartment..
This is quickly becoming my favorite build thread, I cannot stop looking at the picture in #139. That is a disgustingly awesome ride!
I want it 2" lower. im at 10" from the pavement, I want 8!
ive got fish plates and a monster C notch at my buddys house getting CNC plasma'd
im building it to lay frame, after I get bored of it and bag it.
the easier it is for mama to get in an out of, the better.
ive got fish plates and a monster C notch at my buddys house getting CNC plasma'd
im building it to lay frame, after I get bored of it and bag it.
the easier it is for mama to get in an out of, the better.
most definitely a cowl hood, but the hood closes with the housing and IP.
I have big plans for that engine compartment..
just send the hood my way Brian.
Shadetreemechanic
Full Access Member
That makes sense.
I have a buddy that has a CNC plasma.
awesome dude with a 4wd fairlane.
anyone local that dirt pulls may have seen this in action.
anyway, hes cutting me some c-notches and fish plates.
heres a preview, and a shot of his rig.
awesome dude with a 4wd fairlane.
anyone local that dirt pulls may have seen this in action.
anyway, hes cutting me some c-notches and fish plates.
heres a preview, and a shot of his rig.
You must be registered for see images attach
You must be registered for see images attach
well, the bronco now has 6 good body mounts.
the front clip still has no support, gotta come up with a way to make it happen since my frame rails are above the radiator support.
ive been stayin off my "meds" and now I feel like I have came down with "writers block"
thinking tomorrow morning... a nice fat one over coffee will do the trick.
c-notches will be ready for pick up tomorrow.
excited to finish up the rear suspension, but cant do that until my notches are in.
I HAVE to get this thing out of the shop asap and get to work on that 52.
the front clip still has no support, gotta come up with a way to make it happen since my frame rails are above the radiator support.
ive been stayin off my "meds" and now I feel like I have came down with "writers block"
thinking tomorrow morning... a nice fat one over coffee will do the trick.
c-notches will be ready for pick up tomorrow.
excited to finish up the rear suspension, but cant do that until my notches are in.
I HAVE to get this thing out of the shop asap and get to work on that 52.
Last edited:
morgankshaw
Full Access Member
Man this build is great. I don’t know how I missed it until today!
Youve got me inspired to do a megacrew conversion, but I’ll need to get an extended cab section to weld on my cc.
Cant wait to see how the finished product turns out.
Sent from my iPhone using Tapatalk
Youve got me inspired to do a megacrew conversion, but I’ll need to get an extended cab section to weld on my cc.
Cant wait to see how the finished product turns out.
Sent from my iPhone using Tapatalk
Similar threads
