2 Fuel tank questions.

jaed_43725

Need Quad Cab 4x4
Joined
Mar 21, 2009
Posts
410
Reaction score
5
Location
Lillington/NC
1. Are there some extended fuel tank options for these trucks that roughly bolts into the factory place or an improved location? If it was a big single tank that would be just fine as long as it is centered between the rails.

2. Has anyone here done fuel sumps on the factory tanks? If I was to do it would I be better off switching to an electric lift pump? If so which one?
 

kc0stp

30 Hour Famine
Joined
May 7, 2012
Posts
607
Reaction score
3
Location
Colorado
bronco graveyard has a 45 gallon rear tank thatll bolt up only downside is you have to move the spare tire. Havnt seen anything for the side tank though.
 

jaed_43725

Need Quad Cab 4x4
Joined
Mar 21, 2009
Posts
410
Reaction score
5
Location
Lillington/NC
I would get rid of the side tank for just that 45G one. I never did like it though, it always seemed that if it was full it was unbalancing the vehicle.
 

chris142

Full Access Member
Joined
Apr 15, 2012
Posts
3,007
Reaction score
354
Location
SoCal
I've seen tanks that go in the bed along the sides and around the fender humps.
 

kc0stp

30 Hour Famine
Joined
May 7, 2012
Posts
607
Reaction score
3
Location
Colorado
Its a truck, beyond adding some weight to the rear for winter I could care less about how its distrubted, beyond the 45gal rear far as I know all youve got are in bed options which depending on how much you use your full bed can get you up to 99 gallons additional (max allowed by DOT)
 

RLDSL

Diesel fuel abuser
Joined
Dec 14, 2005
Posts
7,701
Reaction score
22
Location
Arkansas
Its a truck, beyond adding some weight to the rear for winter I could care less about how its distrubted, beyond the 45gal rear far as I know all youve got are in bed options which depending on how much you use your full bed can get you up to 99 gallons additional (max allowed by DOT)

well, you can get around that 99 gal bit with a little gray area. I've got a 150 gal bed tank, but what I used was a 150 gal tank off a big truck that is DOT certified with all its original plates on it and I used the original strap mounts welded and bolted to my bed ( along with a couple of v blocks to keep it from rocking since its not hanging off those straps ) . I can plumb right into the fuel system with that and dont have to do the transfer tank bit
 

jaed_43725

Need Quad Cab 4x4
Joined
Mar 21, 2009
Posts
410
Reaction score
5
Location
Lillington/NC
I use my full bed a good bit. So if I ever need to go bigger or replace one I am going with the 45G one.

But about my 2nd question. Has anyone done a fuel sump? Does anyone see a downside to it with these trucks? Diesel Power did it to their Project Armageddon so I figured it would work here and not let air in when it gets low.
 

cbarm

Full Access Member
Joined
May 27, 2007
Posts
352
Reaction score
0
Location
Medicine Hat, AB
I bought a truck recently with a custom built 40 gal rear tank and the front tank hangs down from the frame by almost 6" and holds about 35 gals. I have a suspicion that its from a Super Duty. I will get some pics of it here when it gets light out...
 

icanfixall

Official GMM hand model
Joined
Apr 10, 2005
Posts
25,858
Reaction score
682
Location
West coast
A company called Transfer Flow makes several side tanks for our trucks plus the rear tank option too. they are expensive and they have a great web site too.
 

kc0stp

30 Hour Famine
Joined
May 7, 2012
Posts
607
Reaction score
3
Location
Colorado
transfer flow only offers for 99+ now unfortunatly, was looking at them a while back but then they took it off their site (suspect they might stilll have a couple or can get them still though)
 

Goose_ss4

Full Access Member
Joined
Feb 1, 2010
Posts
355
Reaction score
41
Location
ca
I was wondering about how they did their fuel pick up and return in diesel power mag? Too

I think about doing it to mine, anyone else?
 

jaed_43725

Need Quad Cab 4x4
Joined
Mar 21, 2009
Posts
410
Reaction score
5
Location
Lillington/NC
The return came back up top using -AN fittings and braided line. I won't be doing braided line cause it's really expensive and there's a bunch of hard line attached to the frame already. I might run it to the hard line though. But they did the whole thing in braided.
 

Latest posts

Forum statistics

Threads
92,999
Posts
1,155,978
Members
26,588
Latest member
Rayfish

Members online

Top