Search results

  1. Jbone36

    "Video" whats this sound bad starter?

    If I crank the pulley with a socket wrench it's hard to turn but can get about one pull or about 3 inches on wrench after that will crank over maybe one revolution and then stick again..very very loud. https://streamable.com/1gkauf
  2. Jbone36

    Too much fuel filtration, microns and WMO

    So my original water separator was leaking air, replaced with goldenrod water separator running after a seachoice electric pump. Im debating installing another filter of smaller micron either before fuel pump or after at the IP. Im planning on running wmo in the coming months. How much...
  3. Jbone36

    Electric fuel pump wont push gas unless engine cranking?

    Sick of air intrusion coming and going trying to hook up facet pump. Ive heard people say in message board you can hook up electric and pump fuel while waiting on glow plugs to cylcle. Well unless im not cranking engine fuel wont move.what am i missing here?
  4. Jbone36

    Can i put old DMF back in after installing SMF?

    Hate to beat a dead horse or open a can of flywheel politics but.. A while back snapped the tailhousing on zf5 decided while in there to do the clutch " worked fine though". After some reading i went with LUK SMF. This thing is loud . And its making me nervous that its killing my trans. When...
  5. Jbone36

    Zf5 manual Replace tail housing w transmission in truck.

    First off thanks Russ from typ4 for coming thru with new tail housing. Can thank you enough for the help. So im trying to get this replaced without taking it out but im sure theres plenty of reasons it has to come out. Its just the guy thats helping me keeps saying why? Also anyone know a...
  6. Jbone36

    ZF5 Transmission tail snapped in half. Am i screwed?

    So i didn't notice that the shifter had been bumped and i was in 4wd and at 60mph my front driveshaft Ujoint exploded and took out the rear tail housing. Completely snapped in half..ratchet strapped back together and it runs and shifts belove it or not with minimal leaks . Cant find a tail...
  7. Jbone36

    Hard shift and squeaking when clutch engage?

    Sorry if im tying up message board lately, im close to getting this thing finally done. Been running the z5 swap from e40d for about a week with no problems. Yesterday its started squeeking loud when clutch was engaged and then next day hard shifts into 1st 2nd and reverse. Have to slam...
  8. Jbone36

    Using oil or atf as fuel?

    Never mind found info here on oil burners under "waste motor oil search" sorry about that.
  9. Jbone36

    Solenoid starter and alternator post location

    Ive got these confused and fried a starter. The large dirty cable toward the cab goes to battery the small red wire with yellow crimp behind it goes to alternator. The clean red wire disconnected goes to the starter relay on the fender. Im confused. Thanks
  10. Jbone36

    Fluid type in 1989 ZF5 and transfer case lubricant

    89 f450 Zf5 4wd...Not trying to open a can of worms but i keep getting different information from mercon in both to gear oil in both to 80 in diffs and transfer?..my shop manual is missing transmission requirements, thanks
  11. Jbone36

    7.3 idi Wont run after installing electric pump

    Removed mechanical , Installed 11 psi s eachoice facet pump. Was running before I replaced mechanical pump but very hard starts and sometimes none without alot of work. Injector rerurn lines and caps are new but now today after installing elec pump if pump is running and i wiggle or press down...
  12. Jbone36

    Dodge Dana 60 kingpin axle in an F450

    What would be the point of this and why?
  13. Jbone36

    88 7.3 donar truck for 92 has no PCM ZF5 swap

    Hey all still at it, this is post number 1 of a couple of questions I have. I have the donar truck "88 superduty with 7.3 IDI which has no PCM. Swapping the 88 engine and trans "Zf5 into 93 superduty automatic E40D the plugs fom engine look like they are going to work but im worried about the...
  14. Jbone36

    Name this transmission "pic inside"

    4wd or 2wd?
  15. Jbone36

    1993 8th digit M with turbo Canada made

    Hey all back at the project finally buying a motor this week. 7.3 or 12v 5.9 but i had a question that will hopefully help me make the choice. Truck is 93 f450 vinnny 2FDLF47MXPCA0877 decoder days no turbo but there was a turbo. Also what years will fit this and whats up with the old engine...
  16. Jbone36

    Will a 99 automatic trans and motor fit in a 92?

    Hey all...ive been reading that they will bolt right up with but with slight electrical modifications but my question is this.. The 92 f350 had a powerstroke with serpentine belt previously as well as firewall beat in tuto accommodate turbo so im assuming the pcm was changed..would the...
  17. Jbone36

    Cut crew cab in half to add ambulance box with pass through

    *Edit.. Nevermind i was just thinking.. putting box on the f250 is a no go..92 f350 dually box would be too wide for the truck. Guess im going to pull the engine and trans from 99 and pop it in the ambo.. it had a 94 powerstroke serpentine in it before so should be good to go.. anyone think of...
  18. Jbone36

    California 94 super duty is trash meow? epa forcing me to scrap my truck!

    Long story short i have an ambulance 1992 super duty 4x4i got about 2 years ago and finally got around to getting it finished. Sold my house and while shopping for a diesel mechanic to install a reman engine and drop 25k in it all mechanics are telling me not to do it because dmv w0nt register...
  19. Jbone36

    No power to truck Battery Cables?

    No power to cab fuses are good..please see vid thanks
  20. Jbone36

    7.3 6.9 IDI Injection pump play or loose?

    Hey all quick question. Im swapping a 6.9 into a truck that was a 7.3. a ot of the parts from the 7.3 came with the truck minus the engine so being newer parts i decided to replace the old 6.9 injection pump with the newer 7.3 , mainly because it looks to be much newer as well as the electronic...
  21. Jbone36

    92 SD 6.9 T Ambulance

    Hey everyone I've learned gang of information from this forum and have gotten pretty far on this project solely based on reading comments on this board. I'm attempting to put a 6.9 turbo in the bay of a 92 super duty 4x4 ambulance that used to house a 7.3 turbo.. I wanted to say thanks for all...

Latest posts

Forum statistics

Threads
91,284
Posts
1,129,789
Members
24,099
Latest member
IDIBronco86

Staff online

Members online

Total: 751 (members: 6, guests: 745)

Share this page

Top