Hot engine light stays on and temp gauge does not move. I recently put a 01 motor in my 96. Changed out all sensors for obs sensors.
Also ISO of radiator and SD fan.
Truck shudders after it shifts into third. Around 50mph under light pedal the whole truck shakes. Changed oil and filter, fuel filter, trans filter and fluid. All u joints are tight. Rear end is tight. New tires.
We're lost! If you get on it it's fine. Turn chip off its better but not gone...
My buddy has a 04 6.0 6 speed. It's starts but when you hit the peddle it starts lopping and won't rev any more. Changed CPS. Unplugged chip. (Bulldog) working on getting a scanner. Just looking for ideas.
97 F250 HD auto 4x4
3.55s turning 16.6!
As the title says at 2000 rpm and up my truck is spitting and blowing white smoke. Idles fine. I do get a lil sputter at hi rpm driving but most of the time this truck is under 55mph. I changed the down pipe. Removed muffler and cat. Truck sounds great. Recently did fuel filter as I found some...
Installed a 3in DP today and now truck won't free rev over 250" and has no power on the road. Floor it any speed and it very slowly builds speed. Floor it at 55-60 and it down shifts and goes no where?! It was fine this morning. Ran 65-70 mph. What to do fellas??
97 F250 HD auto 4x4
3.55s...
I recently towed by bosses car tlr and the truck was shifting in and out of OD. Unplugged tlr and no more issues. Replaced plug... Towed my dads bike tlr today and it was super shifting. Top gear by 30 mph! Un plugged tlr. same thing. Un did wiring for plug. Problems fixed. Also my odometer has...
Bosses 99 reg cab 350 has been making a odd noise on small bumps. Found a bottom shock bolt loose. Replaced both. Kinda like a womp womp thing. Then the 4x4 don't work about a hr ago. Front dirve shaft is spinning. But no action from the tires. New lock outs and u joints. What y'all think..
97...
the generator is rated for 8500 peak watts. And 30 amps. Asking 2500
asking 850
asking 850
asking 850
All stuff is NEW. All stuff is made by Bulldog Industrial in South Carolina and has a two yr warranty. Also all stuff is still wrapped in plastic.
All stuff is half the price of new...
Snap on 250 muscle mig.
Has new Tweco lead. Comes with very lightly used tig and spool set up. Also has suit case on side that comes off for added 10 foot of reach for up high welding or just a lil more reach.
Asking $2000 for while set up. The welder, tig set up and spool gun are 6 yrs old...
Been having shifting issues with my 97 auto PSD. Picked up a TC Cus tranny shop dais it was going. Went to change it and found messed up u joint on rear end. Swapped it out and truck shifted great for two to three days. Then started shifting hard again. So I got a lil grumpy and romped on it...
Looking at more options for engine swaps. Talked to a buddie who is thinking about doing a DT360. Called local diesel shop to see if they wanted to do it. Lol he said hell no your crazy.
What y'all think about this????
97 F250 HD auto 4x4
3.55s turning 16.6!
My TC just went out. Good thing I'm close to home. Guess I need to limp it to the shop and dig in. Napa said $150-$350 depending on size. Good thing I just spent $600 this week on vacation!!
97 F250 HD auto 4x4
3.55s turning 16.6!
Been looking at buying a couple trucks and doing some flipping. Found a triton truck for cheap and was wondering how hard it might be to swap in a 7.3???
97 F250 HD auto 4x4
3.55s turning 16.6!
So I have been having a clank and clunk and pop coming from the rear area. Pulled into the shop and had the boss check it out. Then he says holy shite you gotta see this!!! So I checked it out.
The axle is twisting and making a good bit of noise. Sometimes in rev sometimes in drive. I'm not...
So me and my boss were shooting the crap earlier and looking through a diesel power mag and said hey why not put that turbo on the 99 7.3? We have a 6.0 truck and two 7.3 engines to work with. Any ideas? Maybes it's been talked about.
97 F250 HD auto 4x4
3.55s turning 16.6!
My buddies 350 idles fine and drives ok but if you give it decent pedal it falls flat. I'm not near the truck and just looking to shoot him a few more ideas. I told him to check the tps and ICP and to do a few tests
97 F250 HD auto 4x4
3.55s turning 16.6!
I have a grill guard for a 99 up super duty that is in pretty good shape. Minor surface rust cleans right up. Only issue is bottom step piece is rotting out but I plan to replace it and clean her up. Also has 6" KC lights that need bulbs.
Just putting out to see if there is any interest in it...
Looking to upgrade the turbo on my 97. I heard something about a turbo off a Volvo?? I'm going for baby swamps and intercooler also head studs and turbo back exhaust.
97 F250 HD auto 4x4
3.55s turning 16.6!
Got a few things from the neighbor today and was wondering if anybody was looking for something like this. I am close to Ft Wayne In.
97 F250 HD auto 4x4
3.55s turning 16.6!
Tranny went out. Boss don't wanna fix it. Have used very few parts to fix other truck. Good crew can and front clip. Wants 6000 for whole truck. I'll try to do pics on here but it don't work good from the phone
The bosses new ride is acting up. Sounded like a injector so I checked the manifold temps and cam up with a weak number 8 inj swapped it out and it and a new exhaust back pressure dealeo and cleaned the pipe. Truck runs better when warm but still sounds like injector rattle and ping. The boss...
My boss recently bought a early 99 350 that has a DIY. Cold air set up. The Mass air sensor is not hooked up and we want to know if that makes a big difference in how the truck runs. It does run ok now. It has injector issue we need to address soon. It's not real bad but you can hear it. Esp...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.