After many months of going back and forth, I have decided to sell my truck. I was in the process of starting a Cummins swap (I already had the engine from another truck), but I just don’t have the time and have since sold the Cummins engine and parts. I would like to sell this as a package and...
Hi,
I'm looking for an engine cradle to store a extra 6.9 . I found one made by Allstar Performance ALL10141 that is meant to hold a 460. I don't mind if I have to modify it a little, but would like to have it close to start with.
Here is a link to it at amazon...
I have a 1987 F350 4x4 with a C6 that I would like to pull the engine and transmission without separating. I have removed the transfer case. I have the front clip and radiator support removed. Is it possible to pull the engine and trans together, or should I drop the transmission from the...
Went to remove the drain plug from the transfer case tonight to change the atf and the plug is nearly stripped out (the fill plug is in the same shape). I was using a 3/8 drive extension and it was about to spin, so I stopped. I sprayed it with PB Blaster and will let it sit for the night...
There is a 1988 F Superduty with a flatbed and a 460 engine for sale down the road. It had a sign in it for $500, so I had to stop. It is non op'ed, but will take $284 to register because of weight fees. The truck starts and moves. My main motivation for the truck would be the tranmission...
Hi,
My transmission cooler lines have rubbed together and look dangerously thin. I was thinking about replacing them with braided hose. I have read the adapters that are in the transmission case are 1/8 npt. Has anyone ever taken these out and replaced them with other adapters? I'm just...
Hi Everyone,
When I pulled my waterpump off, there was cavitation gouges in the plate that it bolts to. The gouges are not near to going through the plate as the plate is pretty thick. I wanted to "clean" up these divots so I applied JB-Weld with a razor blade to the spots. I have sanded...
Hello,
I have the water pump off for replacement. Is it just the top two bolt holes that go into the injection pump gear housing or are there others that are not dead end holes?
I would like to run a tap into the holes to clean them up and then blow them out, but don't want to blow a...
Hi,
I have been working on a bypass filter using an Amsoil filter. I was going to plumb the return to a port that is on the front of the head. It is a allen plug that was recommended by CDX825, but I have A/C brackets in the way that prevent a 90 degree fitting from going in there. I also...
Hi,
I'm starting to collect parts to overhaul my cooling system. I have read that the Motorcraft waterpumps are better than some of the other brands. Has anyone tried a waterpump from International. I called Riverview International in Sacramento and they have one in stock for $78. I...
Hi,
I bought a new tach sensor to hopefully fix the irratic tachometer. When installing it should I use a little sealant to prevent oil leaks? The factory one looks like there is some black sealant around the bottom of the nut. The new one did not come with a gasket.
Thanks for any...
I'm considering doing a tranny swap from the C6 to ZF-5. I almost had my hands on a doner truck, but it fell through. So I'm thinking about starting to collect all the pieces I need. I went to the pick and pull and found a manual transmission truck (bricknose), but the pedal assembly was worn...
Hello,
I just finished converting my rear drum brakes to disc. I ended up using brackets from Ruff Stuff Specialities and GM calipers. I bent new brake lines for the axle and used a new braided line for the drop from the frame, and new braided short lines to the calipers. I bled 2 quarts...
Hi everyone,
I finally got my truck running and timed. Many thanks to all that have responded to my questions during this overhaul. I'm very greatful to have found such a great source of info on these trucks.
I'm currently having a problem with the Airdog fuel pump/filter getting very...
Well, I got the truck fired up. Wow, having an electric lift pump really is nice. I didn't even have to glow the plugs (outside temp is in the 90's)
I was putting the air cleaner assembly back on and have this tube that I can't remember where it goes. I removed the CDR, did it have...
I received my Ferret timing adapter tonight. I would like to start up my truck and set the timing (I replaced the IP with a Baby Moose and new BB injectors).
I have a Rotunda Injection pump Rotator tool on order, but they are back ordered until Sept. 28th!!! Doesn't seem like anyone keeps...
Hi everyone, and Thank You for reading this thread.
I'm going to run a road draft tube using the Banks adapter that fits infront of the oil fill. I just finished the install of that tonight (pict attached).
But, I was thinking of running a bypass filter (Amsoil or Filtration Solutions)...
I'm going to drill my manifold tonight and was wondering if anyone had any tips for drilling into cast iron.
I'm planning to drill into the top of the driver side manifold between the back two cylinders. From the research that looks like the common spot. It is also as far back as I can get...
I have decided to swap the C6 for a ZF-5 speed. I found one on craigs close to home. It is from a 1988 F350 4x4 with a 7.3. The tranny and engine are still in the truck. The owner told me that he thinks that it only has about 100k, but it was owned by a garbage company to deliver garbage...
I'm thinking about buying a 28ft 5th wheel that will probably be in the 6000-7000 lb. range. The owners manual says that my truck (1987 F350 CC 4x4 , C6, 4.10) is rated up to 9100 lb trailer weight. I will be pulling it though the Sierras and my truck is NA. Is this too much for the truck at...
Hi,
I remember reading that someone used a Taurus overhead light console in their truck for better interior lights. I'm heading to pick and pull and thought I might look for one. I did a search and looked at the Tech articles, but didn't find anything on this mod. I was wondering what...
Does anyone know if Ford and Dodge stock wheels (SRW) have the same back spacing? There is a set of wheels from a 1994 Dodge with 8 x 6.5 bolt pattern that I'm thinking of purchasing for my 1987 F350. Thanks for any info.
Archie Taylor
Does anyone have a picture of how they modified their wrench to get to the injection pump nuts? I see the one offered by Motorcraft Special Service Tools, but it is only a drawing and it is also $52.
http://fordspecialtools.com/Detail.aspx?id=849
I think I borrowed a crowsfoot to get the...
Hi everyone,
I'm thinking about buying a 26-28 ft travel trailer or 5th wheel in the next couple months. I'm guessing that the trailer will weight between 6000-8000 lbs. loaded. I have a place to park it, but it will involve backing it up a narrow driveway that is uphill. It is maybe 400...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.