Recent content by MARQ2277

  1. M

    Engine Timing and Lack of Black SMOKE (NOT Looking to get Black smoke....just read)

    Leave the timing alone, just turn up the pump a 1/4 turn or so, and hang on.
  2. M

    ok lets see ur idi's

    Now that's funny. I went looking for IDI's and not a one. a saw a bunch of OH Hum every day what ever trucks, but not a single Heart OR Sack. Come on, these trucks are a dime a dozen, show me a real picture, let's see the IDI, not the ugly box enclosing it.
  3. M

    E4OD TRANNY PROBLEMS

    Well, calling all transmission masters. My trans started to slip real bad in drive. And I checked: Fluid levels. fusses and connections. removed the electronic connection, and applied power to all solenoids, and grounded the forward clutch solenoid, lock up, line pressure, and 1st gear...
  4. M

    IDI

    Has any one rebuilt an IDI (7.3), and/or did any high performance work, such as crank, rod, and piston work. I would like to rebuild my 7.3, but add some parts so I can get more hp out of it. I read an article where this guy built a 7.3 idi, and made 1200 hp. Of course I don't wan't to make...
  5. M

    Major Engine Problem 7.3

    yep, your oil cooler,head gasket, or hydrolocking has taken place. sorry brother. yes. the 6.9 is a drop dead drop in without questons. only problem is the weight, it is heavier than you think, and a lot more, it is freakin' very heavy, hheeaavvyy. caution, the engine weighs a lot, and it...
  6. M

    which tranny

    which auto trans did the 1987 F250 6.9 idi have?? Marq
  7. M

    BIO DIESEL VERSUS USED OILS

    Correct. I did some research on the internet, and I found plans on making a wvo line heater using glow plugs, some brass fittings, a thermostate, a relay, and a switch to activate it. All the parts come to less than $50.00, compared to $150 for a vegtherm. I know there are other ways also...
  8. M

    E4OD SHIFTING

    Correct. The line pressure is raised during the entire operation. The resister causes the low solenoid to reduce it's operation, and allowing the high pressure solenoid to remain constaint (beings as you cannot add voltage to the already (or current) voltage (or signal) being sent from the...
  9. M

    BIO DIESEL VERSUS USED OILS

    Yep, I can see clearly now. You guys sure helped clear things up for me. For a minute there, I started to think wvo/wmo could not be done. But after getting your reponses, and researching, I found out that: 1. I need to change any rubber parts and lines. 2. I need to use a heater...
  10. M

    E4OD SHIFTING

    Cool, that's what I needed to know. Thanks bro. Marq
  11. M

    BIO DIESEL VERSUS USED OILS

    Okay, now I think I am getting somewhere. If I use filtered wvo, or wmo (veggie oil/motor oil), my rubber "O" rings, rubber fuel lines will be destroyed. My next question is, somesaid that wvo does not burn all the way. Is that the case, and if so, does anyone know why? I am trying to...
  12. M

    E4OD SHIFTING

    Good job. I am glad you have the set up that you like. That is what's important. Anyway, I have a way to go for payday before I get mine changed out. Oh, by the way, do you know how many watts your 50ohm resister is?? If you do, let me know. Marq
  13. M

    BIO DIESEL VERSUS USED OILS

    In Bio-Diesel, the process is to basically remove Glycerin from the vegetable oil (which ever oil you use), by adding Lye and Methanol. Then there is this long complicated process to wash the bio-diesel (with water, out of all things to remove contaminants, which also absorbs the excess...
  14. M

    BIO DIESEL VERSUS USED OILS

    I guess my confusion is that, why do people chemically (by adding lye and methenol, etc.) process veggie plus filter it if the oil is used; yet I read in this forum that a lot of diesel owners only filter the same veggie oil, and run it in there truck. I still am not getting why don't they...
  15. M

    E4OD SHIFTING

    Right on. Let me know how that 50 Ohm works. I still have the 25 Ohm in mine, but it's still only 3 Watts and gets hot. I will just replace it with a 25 ohm, 25 watt. Marq ________________________________

Latest posts

Forum statistics

Threads
91,284
Posts
1,129,785
Members
24,099
Latest member
IDIBronco86

Members online

Top