Recent content by eatont9999

  1. E

    Coolant in Oil

    This is true especially if the CDR tube is not sealing well to the valley pan. Run the truck for a little while and without burning yourself, feel down around the bottom of the CDR tube and if it feels wet, then that could be the cause of the issues. On the other hand, oil cooler cores can...
  2. E

    Coolant in Oil

    Since the water is clear, I want to say that it is something other than a head gasket. In most cases, a failed head gasket will leave you with milky colored oil or the coolant will be exhausted. Let's try this. Remove your CDR valve and drain everything in it into a clear container. See if...
  3. E

    Worst mpg thread

    The worst I got was about 10MPG before the injection overhaul. After that, and setting the timing, I have seen 21.5MPG on the highway unloaded. I haven't been able to get that again but it happened. I usually get 14-16 mixed driving, unloaded. 16-18+ highway. About 16MPG highway with a 6x12...
  4. E

    Proper way to start 92 7.3 IDI Motor

    My gauge only takes a few seconds to get to its normal reading. I always keep the RPMs under 1500 and my tach is about 200 RPM too high. I verified this with my timing meter. I might need a new tach pickup but I'm not overly worried about it right now.
  5. E

    Proper way to start 92 7.3 IDI Motor

    I don't have a high idle solenoid on my truck. I recently acquired a spare, so hopefully it works. My procedure for starting in the morning is: freezing or above, half throttle while cranking, below freezing, 3/4 throttle while cranking. Once the truck starts, I back off the throttle until my...
  6. E

    89 Dually 99k miles ATS turbo (TX)

    Ha, I saw that truck on CL last week. It looked nice. I might have gone to see it but I had other stuff going on. I bet he sold it already.
  7. E

    85 F350 w/ CAT3208

    Wow, I didn't know you could cram those kind of parts into the F350. It's almost as expensive as a new F350, though. The air brakes are pretty cool, though. You can pull up to the Wal-Marts and release the air brakes and sound like a big rig and then smile and think to yourself, yep, I have...
  8. E

    Drilling for a pyro

    I would go with pulling the crossover pipe before drilling and starting the engine afterward to blow the debris out. It's a lot easier than possibly having to rebuild the turbo and you have a leak to deal with anyway.
  9. E

    damn is my truck going to blow up?(video inside)

    Here is a video of my truck with a bad injector. You can clearly hear the chugging sound coming from the open intake. Take your air pan off, start the truck and if it sounds like the video, you may very well have a bad injector...
  10. E

    damn is my truck going to blow up?(video inside)

    Here is a video of my truck with a bad injector. You can clearly hear the chugging sound coming from the open intake. Take your air pan off, start the truck and if it sounds like the video, you may very well have a bad injector...
  11. E

    Sorry Guys... I'm Down Today

    I guess that's what happens when you take a 3 day tour of Italy; you take a 3 day tour of toiletty as well. Get better soon, bud.
  12. E

    Ok guys, progress sorta halted. Need part.

    The stock grommet may not be the same as the one in the banks gasket kit but if it is: http://www.bankspower.com/products/show/ Part 93312
  13. E

    F-Superduty Hydro Boost Parts

    If you get a chance, could you snap a picture of the after? I think I have a mental picture but not sure.
  14. E

    F-Superduty Hydro Boost Parts

    It will really suck if I lose cruise control to go to hydroboost. Also, my F450 pedal looks to be from a manual trans truck. Has anyone been able to get around the CC switch problem?
  15. E

    This will really make you scratch your head!

    All I can say is ***? How does it even pass inspection with the exhaust running through the cab like that? Cool but what would I do with it?
See more

Latest posts

Forum statistics

Threads
91,328
Posts
1,130,428
Members
24,133
Latest member
Nanohawk

Members online

Total: 585 (members: 10, guests: 575)

Share this page

Top