Lumberjackchuck

Latest activity Postings About

    • Lumberjackchuck
      Lumberjackchuck replied to the thread Expected boost.
      Here’s some added anecdotal data from my experience. When I had Justin’s stage 1 injectors and his drop in turbo with the wastegate...
    • Lumberjackchuck
      Lumberjackchuck replied to the thread EGT questions.
      I think generally electromechanical equipment like your relays and ignition coils will be fine unless it is a VERY large EMP...
    • Lumberjackchuck
      Lumberjackchuck replied to the thread EGT questions.
      Yeah but when you get EMP’d by some high altitude nukes those solid state electronics are done. Also with these advances in the tech...
    • Lumberjackchuck
      Lumberjackchuck reacted to Nero's post in the thread EGT questions with Like Like.
      New exhaust is in, new isspro gauge is in, just waiting on the down pipe and wastegate block off kit. Will probably have to stop this...
    • Lumberjackchuck
      ok, send me a PM with your address and I’ll send them over. good luck diagnosing which one(s) may be leaking.
    • Lumberjackchuck
      I tried that when I was having that problem and sending it actually made it get really stuck open and knocking bad. Sounds like you’re...
    • Lumberjackchuck
      How long does it smoke for? I had the same issue with the stage 1 injectors. On cold starts the truck would smoke a little, up until it...
    • Lumberjackchuck
      Lumberjackchuck reacted to Nero's post in the thread EGT questions with Like Like.
      My finger slipped... Its on order... Oops LOL @ISPKI I have the 6.4 viscous fan clutch with the fancy plastic fan that Ron Loder...
    • Lumberjackchuck
      Lumberjackchuck replied to the thread EGT questions.
      I used Justin’s 3” down pipe with his stage one turbo. I didn’t modify anything to get more clearance. Just wrapped the pipe good, then...
    • Lumberjackchuck
      Lumberjackchuck replied to the thread EGT questions.
      https://a.co/d/eidozQQ I used this kit. Made a huge difference for me. My stock exhaust was too restricted and I had trouble building...
    • Lumberjackchuck
      Lumberjackchuck replied to the thread EGT questions.
      Dang, unloaded with a 110 cc pump I have trouble getting EGTs up to 700. I really have to push the throttle all the way to floor going...
    • Lumberjackchuck
      Lumberjackchuck reacted to Nero's post in the thread Fresh build, smoke, stumped with Like Like.
      So I set the timing, its.... 7... Ish. Went and drove it around the block a few times, I definitely had some residual raw fuel in the...
    • Lumberjackchuck
      Lumberjackchuck reacted to Nero's post in the thread Fresh build, smoke, stumped with Like Like.
      Well got off the phone with Justin not long ago, he tested the injectors and confirmed one was stuck wide open. He took it apart and...
    • Lumberjackchuck
      Lumberjackchuck reacted to Nero's post in the thread Fresh build, smoke, stumped with Like Like.
      Just got off the phone with Justin, he said send the pump and injectors back in. He did say that he was having someone else build pumps...
    • Lumberjackchuck
      Lumberjackchuck reacted to Nero's post in the thread Fresh build, smoke, stumped with Like Like.
      Alright I think I'm getting somewhere. I popped each injector line loose while it was running, see which one cleared out the smoke...
  • Loading…
  • Loading…

Forum statistics

Threads
91,374
Posts
1,131,224
Members
24,171
Latest member
jchellen2
Top