Search results

  1. J

    1995 flywheel question

    I'm swapping a 1995 powerstroke into my 1994 turbo diesel idi truck. I haven't pulled the idi yet and when I built it years ago I used a luk single mass flywheel. My question is can I use that flywheel with an upgraded clutch on my powerstroke?
  2. J

    Power windows

    I just replaced the underdash wiring harness with a used one as well as my underdash power distribution box. Everything works great except I have now power windows or power locks. I'm guessing whatever truck my used replacement harness came from didn't have power windows and locks. Does anyone...
  3. J

    Help identifying plug on under dash wiring harness?

    So long story short my windshield leaked on my 2000 psd 2x4 xlt Crew cab long bed auto truck. The underdash harness and fuse power distribution box corroded and malfunctioned. My dad gave me the truck. I pulled the dash and purchased a used harness and box on ebay. Everything looks good and...
  4. J

    Turbo upgrade?

    Well I think I have hit a wall with my truck and my turbo may be holding me back. I am running an ats turbo with an upgraded exhaust and compressor wheel. I have the upgrade ats turbo outlet housing and a a machined compressor housing with larger compressor wheel. The issue is I make about 14psi...
  5. J

    Waste gate tie back?

    We'll I adjusted my wastegate trying to get boost to 12-15lbs. I have the gate tight enough that I can't go anymore or I can't get the arm on the dowel. I need to get 12-15 psi. Egt's are low and the truck is strong but it has allot more in it. I can see the waste gate opening on my boost gauge...
  6. J

    Build finally finished but issues???

    I finally got my truck going after several years of work and problems. The truck is a 1994 ford f350 7.3idi. I am having problems building boost. The truck will jump to 8psi and stop. I adjusted the waste gate up very tight with no change so now I'm looking at a few things. I am going to look...
  7. J

    ZF5 4X4 crossmember

    I'm looking for a ford 4x4 7.3 zf5 transmission crossmember. If you have one please name your price. Thanks
  8. J

    1996 Build

    This build is my dads. He started with a 1991 7.3L IDI 4x4 diesel. It had about 550,000 miles on it when we got it. Not long after that he decided to switch it to a 5 speed manual trans, and then from there I installed a 1994 factory turbo ATS kit for him and adjusted his fuel pressure and...
  9. J

    Intercooler pipe pics

    Figured I would post up a few pics of my intercooler piping. I made it this afternoon. Its a 7.3L powerstroke intercooler with aluminum tanks. I hope it works ok. Im looking to run 15-18psi. Had to cut holes in the rad support for the cooler tubes
  10. J

    LUK problems

    I have a new (been sitting for a long time installed) LUK clutch in my truck. I split the trans and engine and removed the clutch to make sure the pressure plate and disc were not stuck together. I installed a new clutch master cylinder and slave. The arm works fine and moves the clutch fork...
  11. J

    need slip yoke?

    anyone know what the part number is for a yoke on a 4x4 with manual trans on a 1994 turbo diesel? i need the yoke that goes between the t-case and the rear drive shaft. anyone have a spicer part number?
  12. J

    Couple of problems.

    Maybe you guys can help me figure this stuff out. truck 1994 turbo diesel #1 Im not sure if my glow plug relay is coming on and I know the relay works. The "wait to start" light does not come on. #2 The truck wont start with the key. It has an alarm, I have to jump across the solenoid...
  13. J

    Twin Turbo Build Thread.

    Im sitting here kinda board the weather is crapy and I dont feel like getting out in the wind so I will start this thread. I finally got my engine running that has been built for sometime after fighting some head stud issues. It seems to run great. I was going to pop on my turbo and PSD...
  14. J

    twin turbos

    What turbos are normally used for twin set-ups on these trucks? What size? Trim? A/R ratios? any info would help.
  15. J

    Clutch adjustment?

    Trying to get the clutch on my 94 to work. Its got plenty of fluid and Ive blead the crud out of it. What else can I do to get it to fully operate? The pedal goes down and wont come up. Im not sure if its moving enough either.
  16. J

    Help me pick turbos please.

    Im building a twin turbo set up on my IDI but there not much out there on it if you can imaging. I dont know how to read turbo calc charts or how to size turbos. All I know is smaller A/R means more agressive spool time and I think I have found some turbos to try but Im not sure I was hoping for...
  17. J

    Going twin turbo.

    Hey guys I just got my engine running finally and I have been sitting around thinking about what I dont like about the ATS turbo kit and what I do like about it. In the end I may not change anything but I think I can do better with 2 smaller turbos. I dont need to make anymore power than I...
  18. J

    Finally got the engine running.

    Well today I fired it up minus the turbo. I just put a plug over the turbo oil feed tube I made. I did not have vid cam so I just snapped a still shot. I will get some footage when its up and running with the turbo. Im not sure on it yet but I know one thing. Even though DPS did me wrong on my...
  19. J

    Throttle pedal pressure?

    Im sure this gets asked allot. Is there anyway to make the throttle easyer push down on these trucks? My dads psd has spoiled me and I was wondering if there was some kind of electrical control like the psd has that we can adapt or if there are a few tricks that can make the stock stuff allot...
  20. J

    1996 7.3L powerstroke turbo and parts.

    1996 powerstroke 7.3L turbo. Comes with itake Y-pipe intake plenums and a few other peices. The turbo was pulled from a good running truck and it works perfect. I think it also has the wastegate on it and down pipe housing. $250.00 (not willing to seperate) buyer takes all. Buyer pays...
  21. J

    Propane kits? other mods?

    I finally got the engine back in my truck after fighting a head stud battle and moving for a while. I got in touch with Type 4 waiting on pricing on the compressor side turbo upgrade. I have a new unused DPS upgrade pump (not sure how well that will work after what happened with my studs) Im...
  22. J

    Brake questions on 4X4 conversion

    I converted my 1994 dually to 4X4 using an old Dana 50ttb I used dana 60 hubs on it to convert it to dually use. I am trying to figure out what brakes I need. It looks like I can just use the same brakes as found on a srw truck but I wanted to be sure before I bought any. ??????????
  23. J

    99+PSD lower intakes R&L Bank

    My dad is trying to upgrade his 1996 PSD. He already bought the newer 99+ intake Y pipe but now he needs the two intake manifolds that feed the heads under it. Does anyone know what these are called? Im trying to search for them on ebay and such and I cant find any. If you know where some may be...
  24. J

    Flywheel questions and injectors?

    Hey guys I havent logged in for ages and I am getting close to moving back home so I can finish my truck. My dad is working on his and we have a few questions. He bought a single mass solid flywheel with a luk clutch set up for his 1994 IDI turbo truck. He is thinking about getting another truck...
  25. J

    Turbocompressor housings?????

    I know a while back a few guys odered bigger compressor housings for their turbos and wheels on here. I was wondering what the results were and also how much it cost and wich member was the one that I could contact for information. Any help is great. Thanks.

Latest posts

Forum statistics

Threads
91,306
Posts
1,130,044
Members
24,117
Latest member
olsen726

Members online

Total: 603 (members: 1, guests: 602)

Share this page

Top