anybody have any thoughts on this? I'm not sure how much water is injected with a water injection system, so I don't want to mist too much into the manifold.
I pulled the injectors and glow plugs, cleaned them up and scraped around with a small screwdriver inside the holes. The truck seems to start a little faster but still takes a little cranking.
I've heard that water injection get's rid of coking. I was thinking of taking a spray bottle and...
My Goerend valve body came with instructions for wiring in the resistor but not for hooking up a toggle switch for manually locking the TC. Could anybody tell me the proper way to wire in a switch so that the TC works normally but with the switch off but stays locked with it on? I believe they...
Thanks everybody, I think I'll look into the water injection. The WMO I've been running was actually over half used ATF and it still coked up pretty fast. I may try heating it as well
My truck has been starting pretty hard when the engine is cold. The weather has been 40-60 degrees F outside temp. It starts a little easier if I cycle the glow plugs twice, but still takes 15 seconds or so and stutters a few times before firing. It didn't start doing this until I ran a few...
I can't get my heater to blow heat out the floor vents. I just get heat out of the defroster when it's on mix and I get a little warm air out of the defrost vents when it's on floor as well. Near as I can tell it's a vacuum motor not working as I can hear the vacuum motor activate when I...
So in searching on this forum it sounds like everybody is having quality issues with aftermarket wiper motors. I called the Dealer and they want $158 for a new one which sounded like a pretty good deal for the factory part. The catch is they superceded the part and I'd need a wiring harness...
So my wipers have had a few issues, the motor is very loud, sometimes they are slow (typically when it's could out), sometimes after being on for a while the intermittent turns into low with no delay. Often when this occurs I turn the switch off and they keep on going for few minutes. Today it...
Anything you guys running the higher concentrations are doing to make it run right? It would often die when it was idling at stop lights and such. Other times it would idle fine. Topped off the tank with #2 and it smoothed right out.
Any suggestions would be greatly appreciated
Those of you that use Goldenrod water block filters for your WMO, have you tried taking the filter elements out and letting sit for a couple of days to dry? Just wondering if I'm wasting my time. If nobody has tried this I'll let you know if it works.
Are the finned aluminumn transmisson pan and diff cover a worth while mod?
I plan to tow up to 12,000 pounds, maybe a little more. I only plan to do the free engine mods plus a BHAF.
Any preference as to which brand or vendors?
So I just got my 97 Cummins and plan to follow the advice of many and make guages my first mod. I want to go with a 3 guage pillar mount (pyro, EGT, and trans temp). Any recommendation as to brand or vendor. I don't want to get cheap crap that I'll end up replacing. If anybody makes a pillar...
I searched and see that some people are using the power heated towing mirrors off of later model dodges. Are these a simple installation and are they still powered and heated when installed in place of the power mirrors. Hopefully this afternoon I will become the proud owner of a 97 2500 with...
This is kind of a diagram of what mine looks like. my pump is a Tuthill lube oil transfer pump (LP50) from northern. It's 10 gpm so I run 2 goldenrod filters in parallell since they are rated at 5gpm. for the Ts and fitting I used 3/4 household plumbing stuff Glavenized steel. this set up...
I've heard that wmo increases your EGT's. Should I get a Pyrometer to keep an eye on things? My engine is all stock.
Also anybody have experience not using a water block filter? I'm thinking of just filtering wmo to 3 micron and making sure I don't take from the bottom of the barrel...
so I just got my set up for pumping WMO, bought a 12v Tuthill diesel transfer pump and put a Goldenrod water block filter on it. With the filter on I am maybe pumping 1 gallon a minute tops. I didn't watch to see how fast the oil came out when it first started pumping but a minute in it was...
so I just got my set up for pumping WMO, bought a 12v Tuthill diesel transfer pump and put a Goldenrod water block filter on it. With the filter on I am maybe pumping 1 gallon a minute tops. I didn't watch to see how fast the oil came out when it first started pumping but a minute in it was...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.