Search results

  1. ironworker40

    IDI PARTS

    I have the following parts for sale 8 New not remand BB code Delphi injectors psi matched purchased from Type 4 never used with return line kit Valeo dual mass 11 7/8' flywheel new in box never opened Used injector line set New Motorcraft fan clutch Sold Tiny Tach timing meter Make reasonable...
  2. ironworker40

    IDI Parts

    I have the following parts for sale 8 New BB code delphi injectors psi matched purchased from Type 4 never used with return line kit $700 Valeo dual mass 11 7/8' flywheel new in box never opened $800 Used injector line set $150 New Motorcraft fan clutch $150 All prices plus shipping or pick...
  3. ironworker40

    superduty brakes

    So I have a 1994 F-53 chassis motorhome with 40,000 miles. It has the same brake setup as an OBS f-450. Hydro boost 4 wheel disk. In fact the calipers and pads I know are the same part number as a f 450, both front and rear uses the same calipers and pads. We put new NAPA pads on it and 2 of...
  4. ironworker40

    Zf-5 Drain Plug

    Does anyone have the part number for the o ring for the drain plug? My fill plug has a 1/8'' thick metal washer but there is none on the drain plug. Previous owner must have lost it and it drips slightly. Plug is 22mm x 1.50mm. Thanks
  5. ironworker40

    1999 Brake issue

    http://www.oilburners.net/forums/showthread.php?77303-No-rear-brakes&p=912939#post912939 I Need help please see thread above I posted on power stoke forum.I posted this here due to high traffic and knowledge.
  6. ironworker40

    No rear brakes

    A neighbor needs help. 1999 f-250 diesel 4 wheel disc. After changing rear brake calipers, rotor and pads he bleed brakes, last tueday. He drove truck 15 miles each way to work the next 3 days. Brake pedal was low so today he was re bleeding and I stopped to help him. No air but low pedal. I...
  7. ironworker40

    Factory Aluminum Alcoa Wheels

    For single wheels. What size lug are the nuts supposed to be, 1 1/16 or 7/8?
  8. ironworker40

    Front Leaf Spring Bushings

    I'm going to replace my bushings. What are the advantages and disadvantages of stock vs aftermarket poly bushings? I see rock auto has DORMAN 722015 shackles with both bushings and bolt ( at lest that is what is in the picture) but the are like $86. They have the bushings for $5-7 and bolt for...
  9. ironworker40

    2010 super duty ac condenser

    Has anyone had one develop a leak? No visible damage from rocks . Were in florida and my buddies has a leak so we are drivinv to nj with no ac. Im just wondering if anyone had this problem and what brand did you replace it with. I know this isnt the right forum but im not a member of the other...
  10. ironworker40

    WTB OBS DRIVER KICKPANNEL

    I'm looking for a brown drivers side kickpannel for a 93. I think they called the color Mocha. Thanks
  11. ironworker40

    gauge pod

    I got a glow shift pillar mount Quad gauge pod and it is tight getting gauges to fit in it. Has anyone used another brand thats any better? Its my first time installing a pillar mount pod. Any tips? Has anyone used 2 of the auto meter Dual pillar mounts?
  12. ironworker40

    brake line

    http://www.amazon.com/gp/product/B00VVIQM34/ref=pe_385040_121528360_pd_te_s_wl_im/176-0352260-7050812 I helped someone do brake lines on a s-10 the other day and he had this brake line. It was great to work with, takes flares good and is easily bent without kinks. I never used it before. I was...
  13. ironworker40

    Gear Vendors Or Not

    I thinking of installing a gear venders overdrive for fuel mpg increase. Does anyone out there have a 4:10 geared zf-5 with a gear vendors? What fuel mileage are you getting running 70-75 on highway?
  14. ironworker40

    F-53 chassis engine fan clutch part number

    A little off topic here but I thought maybe one of you would have a parts book and could find the Ford part number for the cooling fan clutch for me . It is a 1994 F-53 motorhome chassis with a 460 gas engine. Ford discontinued it, but with the part number I may be able to find one in old stock...
  15. ironworker40

    Timing and Fuel

    I turned up the fuel screw 1 flat then I checked timing and I was at 7.4. When I set it last time I set it at 8.3. Will turning the fuel screw change it that much? Now I wish I checked it before turning up fuel. Also does moving the timing to 9 or 9.5 change exhaust temperature? Will winter vs...
  16. ironworker40

    Dana 60 Pulling Needle Bearing From Spindle

    Here's how to pull needle bearing out of the spindle with a blind bearing puller. They are a tight press fit so if you don't have the correct tools to do this I suggest taking them to someone who does.
  17. ironworker40

    Lock Out Hubs

    I purchase new superwinch hubs. While they are cheaper than Warn hub they are shorter and create a large gap around wheel cover. So I returned them and got warn hubs which are almost exactly the same as the ford hubs. They only difference in the Warn hubs is they have a bronze bushing instead of...
  18. ironworker40

    Pressing Wheel Bearings

    Here is a little trick to help press wheel bearings. I didn't have a driver large enough for the bearing so I used the old races to press new race into hub. If you cut the old races (I used a 4" grinder with a cutoff wheel) this will allow them to collapse slightly so they wont get stuck in hub...
  19. ironworker40

    OBS tilt nose

    I seen this on craigslist. Interesting, I have never seen one on a truck. I think idioit should put it on that 6 door. It would make working on heads easier. http://cnj.craigslist.org/cto/4964829554.html
  20. ironworker40

    OBS TILT NOSE

    I seen this on craigslist. Interesting, I have never seen one on a truck. I think idioit should put it on that 6 door. It would make working on heads easier. http://cnj.craigslist.org/cto/4964829554.html I seemed to have put this in the powerstoke section. I meant to put it in idi section.
  21. ironworker40

    FYI Grease fitting on double u joint

    There is a grease fitting on some of the double u joint center ball. It is very hard to see and you need a needle grease gun adapter to grease is. Don't overlook this step while greasing you truck or you will have to replace it and possible the yoke welded onto the driveshaft.
  22. ironworker40

    Drive shaft

    Does anyone have the part number for the weld on cv yoke for double cardian front drive shaft? Or the driveshaft tube id and wall thickness? I
  23. ironworker40

    Front End Wander

    My truck has developed a weird front end problem. It will jerk slightly, suddenly one way or the other. Doesn't do it all the time. It did it once back in November. Then didn't do it for weeks. It has been getting worse. If you turn wheels from stop to stop several times it will go away. All the...
  24. ironworker40

    fuel filter bracket

    I saw this on the web and started thinking that this is a good idea to fabricate a bracket to move the fuel filter. It would move it away from #1 injector and glow plug. Also it will allow you to use a longer Racor S3225S 2 MICRON filter, thats why I am considering doing it. I have searched and...
  25. ironworker40

    1993 Factory Service Manual

    I have a powertrain /drivetrain Ford manual For sale $35 plus shipping. Its in good condition all pages intact.

Latest posts

Forum statistics

Threads
91,302
Posts
1,129,950
Members
24,110
Latest member
Lance

Members online

Total: 839 (members: 15, guests: 824)

Share this page

Top