Recent content by LUCKY_LARUE60

  1. LUCKY_LARUE60

    egts why

    Are you saying EGT (ehaust gas temps) 600 to 700 degrees or boost pressure 6 to 7 lbs?
  2. LUCKY_LARUE60

    Need Injectors

    Alot of time it is just the solenoid on top of the injectors and people get soaked for injecrors when for $60 you can replace a solenoid on top of the injector.
  3. LUCKY_LARUE60

    Truck wont start

    One thing to check is the oil level in HPOP res. if for some reason it is low it will not start. Also check the oil pressure gauge while cranking, if you are not seeing pressure it will not not start. If no pressure on gauge look into replacing the LPOP, easy job, new Mellings pump about $90 and...
  4. LUCKY_LARUE60

    tilt wheel in my 89

    The reason the bearing fails is using the steering wheel to pull yourself in. It's a pain to rebuild as the shaft get all wore and a bearing will not ride right any more if you try to put a new bearing in. When My old 87 went I just replaced it.
  5. LUCKY_LARUE60

    driving with broken springs??

    So the main leaf broke, the one with the eye, and the axle has slid back. I would get a come-a-long and pull the axle back in place and put a ratchet strap or better yet a 1/4" chain and small spnap binder on it to hold the axle in place and you are good to go just take it easy. Or just leave...
  6. LUCKY_LARUE60

    Block Heater

    The cord is pretty bad shape, need to replace the cord from the block heater.
  7. LUCKY_LARUE60

    Block Heater

    My sons 92 F350 7.3 IDI needs a block heater cord. Not sure what cord it uses so if anyone has a spare cord I sure could use it or give me a part number. Thanks, Jim
  8. LUCKY_LARUE60

    Oilburners After the Holidays Holiday Party

    I also had a great time and renewing old friendships. Good to know that even if ya don't have a IDI anymore you are still welcome in the group. Thanks Travis.
  9. LUCKY_LARUE60

    What is unusual about this photo?

    I have a Centurion but a 99, that truck in the picture is pretty plain jane.
  10. LUCKY_LARUE60

    f superduty 4x4

    Now that would be a project for sure. Drop in a 2nd generation Cummings, six speed tranny, 2 speed rear end, nice flatbed.
  11. LUCKY_LARUE60

    puting strait axle in a 94 f250

    I thought we were suppose to support people with projects instead of discouraging them, I was on another site where if you didn't belong to a elite group you were either snubbed or chastised for your question. There was one post that really got to me, a new guy had a older power-stroke and...
  12. LUCKY_LARUE60

    powerstroke clutch question

    Here Ya Go The "Lucky Mod" Changing a Dual-Mass to a Single-Mass Flywheel By Jim Williams (Lucky Larue) Click here for Companion photos. When taking out the flywheel be careful as this thing is heavy, and it weighs around 65lbs. One thing if for any reason you have any...
  13. LUCKY_LARUE60

    Having issues with push rods.....

    As for the lifters unless they have flat spots I would use them back. They are roller lifters so the are to subject to wear like flat tappets.
  14. LUCKY_LARUE60

    It seems I have the sickness...

    Ya need some serious medication :rotflmao cookoo
  15. LUCKY_LARUE60

    Power Door Locks

    Thanks Nick
See more

Latest posts

Forum statistics

Threads
91,301
Posts
1,129,947
Members
24,110
Latest member
Lance

Members online

Total: 557 (members: 1, guests: 556)

Share this page

Top