6.9 idi injector return cap leaks

[Clb]

Stop tossing parts at things and figure out what’s wrong

How

 

[Kdo58]

The hoses are larger so it has less pressure on the return caps, but you will have to make a adapter to replace the one near the back of the motor, which goes back to the fuel tank.

 

[Cole_Sudeyko]

Just a different co figuration of caps. Tees and elbows in different spots. Same diameters for O rings.

What are you lubcricating your o rings with? I will either buy a harbor freight box of misc o rings, or get a set from a vendor, and I lube them up with a glob of vaseline. Rarely have one leak.

I was just using some lubriplate assembly grease

 

[asmith]

Try vaseline. that has seemed to work the best for me. Also I haven't seen it mentioned yet, and maybe you are already doing this, but just in case. put the top oring on first then GENTLY roll the bottom one over it into the bottom groove. This can help prevent them from getting nicked.

 

[Cole_Sudeyko]

Try vaseline. that has seemed to work the best for me. Also I haven't seen it mentioned yet, and maybe you are already doing this, but just in case. put the top oring on first then GENTLY roll the bottom one over it into the bottom groove. This can help prevent them from getting nicked.

I’ll give that a try thank you!!

 

[Nero]

Vaseline, and Super Lube synthetic grease are what most people use.

 

[scsmith42]

I use Dupont Molykote 55 o-ring grease with all hydraulic and fuel system o-rings. It's made specifically for lubricating 0-rings.

Although I buy it from my local industrial supply house, it's available on Amazon.

Amazon.com: MOLYKOTE 55 O-Ring Grease 5.3OZ D632745 : Automotive

Buy MOLYKOTE 55 O-Ring Grease 5.3OZ D632745: Grease Guns - Amazon.com ✓ FREE DELIVERY possible on eligible purchases

www.amazon.com

 

[nelstomlinson]

CDD and R&D both sell return kits that should be the best quality available.
Dregs Garage occasionally makes a run of very nice brass return caps. I've had excellent success with those, but they're expensive, and shouldn't be necessary.

 

[Tod Rockstead]

Ok, assuming you've obtained all the correct parts... let's talk about how you're installing them.

​

1. Remove everything. Pull both sides of the entire fuel‑return assemblies. Replacing one or a few caps is pointless.
2. Get supplies. From NAPA:
   • Clear diesel‑rated return hose (correct size)
   • 1 quart ATF transmission fluid
3. Rebuild the return assemblies. Use the old assemblies as your guide. Lubricate each cup nipple with ATF before installing the new hose.
4. Prep the injectors. Remove both O‑rings from every injector. Wipe each injector clean.
5. Prep the new O‑rings. Pour some ATF into a small cup. Drop all new O‑rings into the fluid so they’re fully coated.
6. Lubricate the injectors and cups. Generously coat:
   • The tops of all injectors
   • The inner surfaces of all return cups with clean ATF.
7. Install the O‑rings correctly (corrected). Place the first O‑ring into the first groove of the injector. Install the second O‑ring below it.
8. Seat the return rails. Set the rails over the injectors and press firmly until you feel the cups fully seat.

The clear line helps diagnose air intrusion. Do yourself a favor and ditch the mechanical lift pump. I replaced mine after 2 bad pumps back-to-back from AutoZone with an Edelbrock Green Micro E Pump for diesel fuel.


1986 Ford F250 XLT SC LB 6.9 IDI Banks Sidewinder Gen1 C6 Auto 4x4 with GearVendor OD 74K original miles only. 6" lift & 34" all terrains on American Racing "Outlaw 2" wheels

 

[nelstomlinson]

Tod, can you give us a source or a link for that clear hose?

 

[Tod Rockstead]

You must be registered for see images

Fuel Line, ID: 1/8", OD: 1/4", 50'


Part #: SME 188150
Napa Auto Parts

You must be registered for see images

Fuel Line, ID 3/16", OD 5/16", 50'


Part #: SME 188151

https://www.napaonline.com/en/search?text=diesel%20clear%20fuel%20line&referer=v2

 

[Tod Rockstead]

“I walked into my local NAPA and asked for clear fuel line that’s rated for diesel. Since it’s part of the return system, it’s on the low‑pressure side, so that type of hose is perfectly fine.”
“If it were me, I’d call NAPA first and have them confirm the part number for the diesel‑rated hose. I bought one identical to the hose shown in the picture.” It worked and is still in use on my entire fuel return system from the port next to the Schrader valve to the return line. “I ran a new line from the selector valve to the Edelbrock electric micro‑pump mounted high on the frame, just past the tank selector. I ditched that garbage hard blue plastic line and replaced it with proper heavy black fuel hose. I removed the POS lift pump entirely and fabricated a block‑off plate using a generic AutoZone cover that happened to have the correct bolt spacing. I trimmed the excess metal off the plate with a bench grinder and shortened the original bolts by about 3/8 inch.

I removed the loop on the lift‑pump inlet side, hacksawed the flare‑nut end off the metal line going to the filter, and installed the recommended Edelbrock fuel‑pump relay kit. The injector pump’s FSS wire is used as the trigger to open the relay and power the micro electric pump.

Since doing all this, I haven’t had a single issue with the fuel system — the engine fires before the starter even makes a full revolution.”**

 

[Black dawg]

Any long term results with the clear hose? Do the clamps fit it correctly?
My experience with that type of hose is that it gets dried out and stiff very quickly, leading to leaks. Maybe it was the brand I have used? Also from napa.