Search results

  1. haubert

    zf5 swap no start

    Thanks cpdenton that will save me a lot of time I have all data but it's hard to find the correct diagrams
  2. haubert

    zf5 swap no start

    93 f350 7.3 I installed a fresh rebuilt 7.3 while I was at it I swapped out the e4od tranny with a zf5, I installed a factory manual steering column, I don't have no neutral safety switch hooked up and I removed the e4od wiring harness from the truck, everything seems to work when I turn the key...
  3. haubert

    zf5 swap

    Ok thanks Sent from my SCH-I545 using Tapatalk
  4. haubert

    zf5 swap

    I have a 93 7.3idi swapped out the e40d with a zf5 also installed the single mass flywheel clutch conversion kit. getting ready to instal the clutch brake assy. my question is im not sure if theres a particular slave cyl that I need for the single mass. I have a master cyl slave assy from a 91...
  5. haubert

    Transcommand for E4OD

    I'll take second in line
  6. haubert

    E4od to 5 spd swap

    Ok thanks, I appreciate All the forums advice. Can't afford to learn by, my own mistakes LOL
  7. haubert

    E4od to 5 spd swap

    Anyone know if the 5th gear is 1:1 also thanks now will the newer 6 spd bolt right up. Just trying to figure out if I'm going to need a gear vendor unit for the highway running when I switch over to manual thanks
  8. haubert

    E4od to 5 spd swap

    Forgot to add my truck is a 93 f350 7.3
  9. haubert

    E4od to 5 spd swap

    I was at the scrap yard today looking for a 5 spd tranny looking to convert from my e4od. All I could find were older 4 spd what do you think of the 4 spd or should I hold out. I use the truck for heavy pulling are the final gears the same ratio
  10. haubert

    What temp sensor

    Ok thanks for the schooling my truck is a 93 just assumed being to sensors one was for computer like a gasser thanks Sent from my SCH-I545 using Tapatalk
  11. haubert

    What temp sensor

    Ok thanks that's the sensor I removed to install guage it's a single wire. Just wanted to make sure it wasn't the temp sensor for computer Sent from my SCH-I545 using Tapatalk
  12. haubert

    What temp sensor

    What i was trying to say i installing a coolant temp guage what's the location for guage sending unit and computer sending unit Sent from my SCH-I545 using Tapatalk
  13. haubert

    What temp sensor

    I installed a coolant temp sensor. I thought the sensor on the driver side front head is for guage. Installed probe hooked up guage and my in dash guage still works. Did I remove the wrong sensor or will the computer sensor reads to guage also Sent from my SCH-I545 using Tapatalk
  14. haubert

    Exhaust

    That's a good deal. Let us know how it fits. Sent from my SCH-I545 using Tapatalk
  15. haubert

    QUICK QUESTION ABOUT INJECTOR CODES.

    I'm running the United technologies code b in my 93 7.3 runs fine for $40 buy them you could always have them pop tested before installing if your unsure Sent from my SCH-I545 using Tapatalk
  16. haubert

    need new valves or new engine.. what would you do?

    Did you warm up truck before compression test? Did you do compression test while replacing injectors and before start up. If so possible injector did not properly seat due to carbon. Start truck warm up and retest Sent from my SCH-i705 using Tapatalk
  17. haubert

    Electric fan conversion help

    I'm converting my cooling system over to electric, I have a new 3 core radiator ordered, I bought the 95-98 windstar fan assy, I didnot order the windstar control so I have no wire harness, any one have the part numbers for the pigtails one is a 2 wire other is 3 wire, I'm also assuming the...
  18. haubert

    7.3 turbo idi help

    Not sure, I looked it up on my code chart for my 93 thought it would be the same Sent from my SCH-i705 using Tapatalk
  19. haubert

    7.3 turbo idi help

    Code 94 Torque converter solenoid circuit failure Sent from my SCH-i705 using Tapatalk
  20. haubert

    Nice truck

    I thought it was foam, but sire looks like ice Sent from my ADR6410LVW using Tapatalk
  21. haubert

    1993 IDI regular cab - parts available

    Pm sent Sent from my ADR6410LVW using Tapatalk
  22. haubert

    Car seats n the 85 350

    I have a 93 crew cab with aftermarket bucket seats front and back, I use a car seat that also has the snaps to secure to a steel lope on the seatbelt mounts, you can pickup from a junk yard, be sure to measure properly the first set I bought were to long and put the latch in the babies back, if...
  23. haubert

    Stock compression

    Just checked my compression to see if its worthy of a turbo installation 93 7.3idi 280,000 on odometer, just bought the truck last year I don't know nothing about it motor warm lowest 400 high 450 seams almost to good for those miles anyone know what compression is from factory Sent from my...
  24. haubert

    lift pump

    What's the member name on the carrier facet pumps, I'm looking to do the conversion also just wasn't sure were to buy thanks Sent from my ADR6410LVW using Tapatalk
  25. haubert

    It's official...

    Interesting thread, I had the same thing happen, #3 was so carboned had to use a breaker bar to fully unthread and pet injector out, #2 injector unthreaded I had bad thoughts bit removed spring and needle removed, had my shop machine the upper threads off the injector,got home screwed the...

Latest posts

Forum statistics

Threads
91,332
Posts
1,130,495
Members
24,133
Latest member
Nanohawk

Members online

Total: 719 (members: 9, guests: 710)

Share this page

Top