Search results

  1. 9

    7.3 idi lost oil pressure

    I removed the oil filter, and found that the pressure regulator was stuck. I took a pick and kept working with it till it was freed up. I took the mechanical pressure gauge line loose from the top of the engine, and moved it to one of the oil plugs in the block near the oil filter. Started the...
  2. 9

    7.3 idi lost oil pressure

    I still have the factory oil pump. I think all those parts were boxed up after the rebuild. Don't mean to ask dumb questions, but you don't know if you don't ask. Is there a way to check a oil pump to see if it's good?
  3. 9

    7.3 idi lost oil pressure

    Thanks to everyone for help. I'm going to take off the oil filter, see what I can find, if nothing there, I'll pull the oil cooler off and go deeper. If the valves in the oil cooler isn't the problem, where should I look next? Thanks again guys, all help is greatly appreciated.
  4. 9

    7.3 idi lost oil pressure

    The mechanical gauge is teed into the oil line going to the turbo. Would you guys happen to have a couple pics on the oil regulator? If the oil cooler has to come off, how hard is it to remove from the engine? Thanks again.
  5. 9

    7.3 idi lost oil pressure

    Hey guys, been a while since I was here, but knew where to come to for the best help. I'm looking for help on a oil pressure loss problem. I've got a 7.3 idi with less than a 1000 miles on it since a complete overhaul. .040 bore, new cam and cam bearings, new rod and main bearings, new oil pump...
  6. 9

    4 Inch Exhaust Build Plan

    You might want to check out alligatorperformance.com, they have a 4" kit for the 94 - 97 psd made by diamond eye exhaust. This kit has a 2 piece 3" down pipe that goes into a 4" just under the front of the cab. Took me about 2 hours to remove the old exhaust and reinstall the 4" kit. It come...
  7. 9

    Little extra rattle in 7.3

    I did use a click type torque wrench. Never crossed my mind to double check with the other wrench. But hey, lessons learned aren`t soon forgotten. I got the motor back out of the truck, and pulled the oil pan. When i got the pan off and got to the rod, it had one bolt in the rod that was broke...
  8. 9

    Little extra rattle in 7.3

    After i got the oil pan off, about a 3 inch chunk of the block fell off, all the way up to the motor mount. Time to start over from scratch. Good thing i kept the old motor out of the truck.
  9. 9

    Little extra rattle in 7.3

    I finally found out what my noise was, and I must say i didnt like what i found. I changed out my injectors, bled the lines, fired it up, and a rod came thru the oil pan and the block. All that work, time, and money, shot to hell.:puke: -cuss:puke:-cuss:puke:-cuss
  10. 9

    Banks downpipe

    Does anyone know if downpipe gaskets are still available for the early nonwastegated setup ? I know its been sometime since Banks produced this turbo setup, but just seeing what is available. Does anyone have a part number for the gaskets ? thanks
  11. 9

    Little extra rattle in 7.3

    Would it be possible that a glow plug could cause the knock ? I checked all the injectors none seemed to have an effect on the engine. But in the process of checking out the injectors, i found a glow plug that looked like it had been damaged somehow. Would it be possible that the injectors were...
  12. 9

    Little extra rattle in 7.3

    I changed the flywheel from a dmf to a solid before i put the engine back in the truck. I don`t think the flywheel would cause this kind of knock. The engine came out of another truck that the automatic transmission went out in. It was overhauled not to long before i purchased it. I heard the...
  13. 9

    Little extra rattle in 7.3

    I finally got the motor in and started it up. While i was letting the truck run for a few minutes, to check for any leaks,i started getting this little clicking noise. The longer the truck ran the louder the noise got. Now the clicking sound has gone from a click, to what sounds like a full...
  14. 9

    Best source for Banks parts

    Most of the parts you are looking for can be purchased directly from Banks. I ordered a block off plate and o ring, a oil to turbo supply line, and a oil drain line from them, and the customer service guys were great. If you have the part numbers to your missing parts, they can have what you...
  15. 9

    Banks non wastegated turbo question....

    I knew this was gonna be a tough install, but i never dreamed it would be anything like this. I`ll probably take the hammer and free up a little space, as opposed to a body lift. Slowly but surely everything is coming together. Heres where i am up to this point. I took the 7.3 all the way down...
  16. 9

    Banks non wastegated turbo question....

    I`ve checked for any obstructions, nothing seems to be touching anywhere except the top of the cold side of the turbo is hitting the firewall just below the vacuum hoses. not sure what is causing it tho. Would like to find some pictures of one that has been installed just to see, and get a fill...
  17. 9

    Banks non wastegated turbo question....

    I`ve been working on installing my early banks non wastegated turbo set up, and have had a heck of a time getting my up pipes to all line up. The guy i purchased the setup from must have tied to the pipe and pulled it out instead off unbolting it, nothing wanted to line up. Well after many cuss...
  18. 9

    Banks Non Wastegated Turbo...

    Hey Guys, Does anyone have a copy of the installation guide for the banks non wastegated turbo set up ? I`m going to start an install next week, and was hoping to someone might have a copy or have a link i could go to and print. Any help or suggestions for finding this info would be greatly...
  19. 9

    new solid clutch ??

    Hey Guys, Who has the best prices on a new solid flywheel and clutch set for the 7.3 ? Not really looking to drop a lot of cash on a new set up, but gotta do something, pulled the flywheel of my engine, and two of the springs were all but gone and the rest were broken in the DMF. Looking to...
  20. 9

    Engine stand

    ;Sweet...... Thanks for the info. I bolted it to one of those Harbour Freight #750 stands and it never even slowed it down on its way to the floor as i let the hoist down. Thanks
  21. 9

    Engine stand

    Going to freshen up a 7.3, and i`m looking for a stand to hang the motor on. Who makes the safest, least expensive engine stand that will bolt to the engine, and not collapse ? Thanks
  22. 9

    Banks Turbo questions

    the turbo setup that i bought was a used non wastegated unit, not sure if its the same as the wastegated or not. I pulled the cdr off the back of the intake and put the turbo mount on the back off the head, just to see where everything was gonna sit. The oil oil drain tube doesn`t even reach the...
  23. 9

    Banks Turbo questions

    Thanks. The few parts i`m looking for are things like the crankcase vent adapter, oil supply line to the turbo, oil pressure sending unit relocater. The vent adapter i could make no problem, and probably come up with a oil supply line, i`m just a little picky when it comes to looks on my truck...
  24. 9

    Banks Turbo questions

    Are there any parts still available from banks for there idi turbo kits ? I trying to round up all my parts before i pull the truck in the garage and start the install. How much modification to the firewall will need to be done to get the up and down pipes in there? thanks for the help
  25. 9

    7.3 idi questions

    Thanks Chris. Would you happen to have the part number for the kit you have ? Are you running a straight pipe, or muffler setup?

Latest posts

Forum statistics

Threads
91,304
Posts
1,129,966
Members
24,110
Latest member
Lance

Members online

Total: 680 (members: 9, guests: 671)

Share this page

Top