Search results

  1. kbenz

    sporadic oil leak

    I been losing oil sporadically. Pulled in the driveway and backed around and parked. bout 10 minutes later i walked by the front and noticed two oil trails in the gravel. started back up and nothing was leaking. lost a quart of oil. what would cause a sporadic leak? the paths went to...
  2. kbenz

    water injection

    amazon has these pumps for 52% off. Seems like they was around $120 when northern tool carried them https://www.amazon.com/gp/product/B07N7JW49R/ref=ox_sc_saved_title_2?smid=AF8EGQ3KRZQB6&psc=1 I bought one. been wanting to do some water injection on my truck. Too dang hot to mess with it much...
  3. kbenz

    sticking valve

    I think I have an exhaust valve sticking. once it warms up good it starts huffing out the air intake. Is there an oil additive that will help or am I pulling a head? Thanks
  4. kbenz

    7.3idi swap

    Thinking bout putting my 7.3idi/zf5 in my 65 Chevy c60. How do you think it’ll do with the 2 speed rearend?
  5. kbenz

    Trap

    Who uses a water trap on their input/output on your centrifuge setup? Got any pics? Thanks
  6. kbenz

    flat towing?

    I use my f350 mostly to flat tow my hunting truck. problem I'm running into is no tongue weight which doesn't help with traction (stopping or starting) If I hit the brakes too hard the back brakes will lock up. someone told me to remove some springs? not too sure about that. If adding weight is...
  7. kbenz

    high idle plunger

    Mine is gone. not sure what happened. I ran a magnet through the valley pan best I could and turned up nothing. Where and what am I looking for as far as getting another one?
  8. kbenz

    Blower motor

    When I first turn on my ac it blows good and strong. After about an hour it dies down. Where should I start looking?
  9. kbenz

    7 blade trailer plug

    I was looking up 7 blade wiring diagrams. I didn’t realize there were different variations of it. Is there an actual standard for it? Or most common at least
  10. kbenz

    clutch slave bore

    whats the bore size of a stock slave cylinder? thanks
  11. kbenz

    Stack

    I know it’s frowned upon by most but when I hit a hill pulling anything or just getting on it getting up to speed it smokes pretty bad. I really don’t like it. It seems kinda obnoxious at times. It’s a crew cab so I do have room for a muffler. I built this stack out of 3x3x3/16” tube. Questions...
  12. kbenz

    Rug source

    Found a source for some rug but has trash and water in it. Should I just settle it out? Or mix with oil before I run it through the centrifuge? Or both?
  13. kbenz

    Electrical issue

    This rough looking wire set is attached to the hot side of the starter relay. I have a 5.6amp parasitic draw on them wires. I’m guessing they feed the fuseblocks. I pulled all the fuses with no change in draw. Any ideas things to check? Just started doing this
  14. kbenz

    Gooseneck

    My bed on my 93 f350 was cutoff 16” in the front to make room for a wheel lift that is no longer there. Now I have a bed with a mount for a ball roughly 17” in front of the axle. I don’t have a gooseneck trailer but if I needed to would that be any issue?
  15. kbenz

    Blend door

    93 f350. Pulled the cover off and found a small carriage bolt blocking the movement of the door. While removing that, the piece that sticks up from the blend door to the cable actuator broke. Any idea on how to fix it? Thanks
  16. kbenz

    heat/ac controls

    93 F350. The dash switch with the vacuum lines broke. What are my options here. Doesn't look like any of these are being produced anymore. Thanks
  17. kbenz

    starts then dies

    93 7.3 non turbo. electric fuel pump. 6# fuel pressure after the filter. starts fine cold. hot it will start and run if you crank it soon after shutting down. If you wait 30 minutes it will start and stumble then die. Then it's a ***** to get going again. did the cold water on the ip with no...
  18. kbenz

    clutch master?

    What size bore for the zf-5 clutch master cylinder 3/4" or 1"
  19. kbenz

    o rings?

    I found the 111 viton o rings but they come in 75a and 90a durometer? which one or does it matter? thanks
  20. kbenz

    swap question

    looking at a 89 model single wheel f350 4wd. how much would be involved in putting the 4wd front in a 93 model dual wheeled f350? Are the frames similar?
  21. kbenz

    another possible cab swap

    Thinking about pulling my 93 f350 crewcab off and mounting a 65 c50 on it. Anyone done one similar?
  22. kbenz

    Wheels

    Looking at a 73 c50 with the elusive 20" wheels. I've been reading that semi truck wheels will bolt up? Which are the best to go with? This will be a work truck, nothing fancy. Thanks
  23. kbenz

    rv 460 fuel pump

    87 E350 460 RV. I believe the fuel pump is in tank? If it is can I add an inline on the frame if the one in the tank isn't working or do I need to pull the tank?
  24. kbenz

    no heat

    I have a 96 motor stroked to a 383 in my 64 gmc. 20,000miles approx. Put a serpentine setup on about 3 months ago (along with new water pump) Motor seems to be cooling fine but I have no flow coming out of the pump for the heater. I can put a hosepipe to the return side and water flows out the...
  25. kbenz

    Fuel filter head

    mine doesn't seal right. I have to use a filter wrench to tighten to were it won't leak. What are the options for replacement?

Latest posts

Forum statistics

Threads
92,997
Posts
1,155,937
Members
26,574
Latest member
sramasya

Members online

Total: 1,588 (members: 12, guests: 1,576)

Share this page

Top