Search results

  1. ddec4me

    fuel pressure test fitting?

    :dunno I have have been needing to do a fuel pressure test on a friends powerstroke. I found the ports to tap into the fuel filter housing. My fuel pressure test kit does not have a fitting to tap into these ports. What thread ist this fitting? It is not a taperd thread that I can tell. Is it...
  2. ddec4me

    Garret Turbo ID

    I was curious last night. One of my Techs was replacing the turbo on a DT466 I notice the turbo was a garret The tag on the turbo was gone but The casting had numbers in it. .60 M24. I took the housing out and compared it ti my turbo and the turbine housing had similar casted #s. .70 m45 if I...
  3. ddec4me

    Body Lift???

    :dunno I have been searching this evening for a body lift. Just 2"-3" to add a little extra room. Then after I do my solid axle swap I will go a couple more inches with the suspension giving me plenty of lift. My Dilema is that every lift I have found so far say Excludes Diesel Engine. Why is...
  4. ddec4me

    Guage Readings

    Last weekend I finally took care of a couple of small projects I have been planning. 1-Fuel return lines. The kit I bought of ebay was really good especially for $25 2-Installed Pyro and Boost Guages. 3-Mocked up Cold air pipe Here is what I have observed. Driving unloaded on country...
  5. ddec4me

    One More Trip To The Store!!!!!

    We have all had those days where we work our butt off from morning till night and dont get a dang thing accomplished. Yesterday morning I started off on a roll that went rapidly downhill.:mad: I have been putting off a couple of projects due to finishing some cleaning up and wiring in my new...
  6. ddec4me

    EGT Sensor Location

    I am getting ready to install my EGT sensor and guage in the next couple of days and was wondering the best location for my sensor. I have the upgraded outlet on my turbo that is a 3" id elbow that goes down about 6" then my downpipe slips into it. I was thinking about just drilling a hole and...
  7. ddec4me

    Pensacola Diesel

    I was surfin ebay today and saw a seller named Pensacola Diesel. Anyone have any experience with this outfit.They have some prices that seem to be really good but dont want to buy junk!:dunno
  8. ddec4me

    Battery Relocation

    Ok now that my Exhaust project is done I am heading towards the intake side of my turbo. I am considering locating a cone filter setup like the one agnem shows in his photo album. If I move my battery I will get a better flow of cooler air. I was thinking of moving both batteries into my toolbox...
  9. ddec4me

    Turbo ??????????

    I work on diesels all day long but never V8 navistars. I have worked on alot of DT466 engines but 95% of my experience is either Detroit 60, MBE(Silver POS) and ISB,ISC,and the Big Cummins. So Humor Me If my questions seem stupid. I have this '93 F250 That I bought wrecked for $1000. I have...
  10. ddec4me

    exhaust adapters

    I am building my own 4" exhaust. I have all of the pipe sections and bends that I have collected from various repairs done at work. However I need to find a good source to buy my adapters from my stock Exhaust to 4" as close to the turbo as possible and then from 4" to a 5" tip that I have made...
  11. ddec4me

    ANY SUGGESTIONS!!!!!!

    So this weekend my plans are to do a fuel return line kit to stop the small leaks on top of my engine. This is a pretty straight forward procedure I have done several times at work.and I have a 4" galvenized stack pipe off of a small international 4000 series that I plan to turn into my muffler...

Latest posts

Forum statistics

Threads
91,376
Posts
1,131,358
Members
24,177
Latest member
RangerDanger

Members online

Total: 533 (members: 12, guests: 521)

Share this page

Top