Recent content by Therkhan7_3Turbo

  1. T

    So what did you do with your truck today?

    Got a ladder and cleaned off my room, always have to take a picture from overhead when you can.
  2. T

    Tachometer adjustment ?

    Didn't think of that I may run a jumper to a good ground and see if it makes it better. I'm driving with the front of cluster off right now as k was adjusting the speedo calibration. Sent from my LM-G710 using Tapatalk
  3. T

    Tachometer adjustment ?

    The plastic mother board thing is all corroded but I can't seem to find a replacement online, everything else is great... I might have to test traces with resistance. Sent from my LM-G710 using Tapatalk
  4. T

    Tachometer adjustment ?

    Brand New and everything is good. No gunk on the magnet either. The whole harness as far as I can tell is clean. Sent from my LM-G710 using Tapatalk
  5. T

    Tachometer adjustment ?

    I apologize. 94 f250 idiT with am E40D. Sent from my LM-G710 using Tapatalk
  6. T

    Tachometer adjustment ?

    I remember seeing in some random thread that there was a way to adjust the tach? There is this white potentiometer? On abck of the tach is this an adjustment ? My tach just goes nuts when wide open and pegs 4500rpm.... Tach sensor is new, and the gear is good in shape. Wiring seems okay ...
  7. T

    94 F250 Cluster

    I might go to the yard and see if I can find a better one, I need bunch of interior pieces, damn Florida sun and old 90s plastic...
  8. T

    94 F250 Cluster

    So I pulled my cluster out, because my speedo is wiggling ( I just cleaned the VSS ) and the Tachometer is useless, even with a brand new sensor and I haven't seen any wire damage, it just likes to go to 4500rpm when I go wide open. Well the circuit board, that's that ****** plastic is all...
  9. T

    94 F250 Cluster

    So I pulled my cluster out, because my speedo is wiggling ( I just cleaned the VSS ) and the Tachometer is useless, even with a brand new sensor and I haven't seen any wire damage, it just likes to go to 4500rpm when I go wide open. Well the circuit board, that's that ****** plastic is all...
  10. T

    Should I grab this intercooler?

    Anything will be good for an IDI. I haven't installed an intercooler on an IDI But thag doesnt look too big, compared to some I've seen installed. The only issue is the one side inlet and outlet, you're going to have a crammed passenger side engine compartment. Sent from my LM-G710 using...
  11. T

    So what did you do with your truck today?

    Really ? I feel like my IDI is the most pissed off truck ever if the batteries aren't 100% all the time.... Maybe my cables are trash... Sent from my LM-G710 using Tapatalk
  12. T

    So what did you do with your truck today?

    The worry with the high compression and stuff that a single battery unless your fuel system is 100% air tight with zero issues, I'd worry... Sent from my LM-G710 using Tapatalk
  13. T

    So what did you do with your truck today?

    I'll be honest... Get the cheap ones if you're trying to get it going in a budget. My 12v had cheap 40$ reman batteries in it forever. Not particularly cold where I live currently, but we'd even plug in our gassers in my hometown (Quebec). Sent from my LM-G710 using Tapatalk
  14. T

    So what did you do with your truck today?

    Batteries are better than bad batteries.. No matter the price. I have Duracell batteries from Sam's club and they're awesome... 89$ a piece. Sent from my LM-G710 using Tapatalk
  15. T

    Tachometer issue 94

    Brand new out of the box Ford sensor. Old one looked new too. Sent from my LM-G710 using Tapatalk
See more

Latest posts

Forum statistics

Threads
91,280
Posts
1,129,764
Members
24,098
Latest member
William88

Members online

Total: 833 (members: 6, guests: 827)

Share this page

Top