Recent content by international

  1. international

    E4OD hard shifts

    I chased my teeth braking shifts forever to no avail. I also have the issue of it not shifting to the next gear unless I let off the gas. Doesn't matter if it's fast or slow acceleration. Luckily I parked the truck for awhile. Now that I'm getting it back on the road I will dig yet again to find...
  2. international

    So what did you do with your truck today?

    Dug out the 1994 that's been sitting for four years. Time to get some work done. Miss the sound of it.
  3. international

    Soft Brake Pedal

    I parked my truck four years ago. Also stopped logging on here a couple years ago. Decided it may be time to put it back on the road. Not so surprisingly the wire from the starter to the solenoid has crumbled into nothingness. Another issue I had was the brake pedal slowly sinking to the floor...
  4. international

    Stock Downpipe Wanted

    I have one in Columbus. Headed any further west anytime soon? I may be in Pittsburg within the next month.
  5. international

    Educate me please. E4od's and torque converters

    Umm, won't an unlocked TC generate more heat than a locked one. Unlocked = slippage = heat.
  6. international

    Fuel leak at filter

    Last week my brass drain screw snapped in half. I have no idea why. I ended up taking it out and using a 1/4" bolt and injector return line oring to seal it for now. Anybody know if you can buy just the brass part with the thumb screw? Talk about a smokey scare. Full pouring onto a hot exhaust...
  7. international

    "Engine Temp" light/sending unit question

    Im going to have to agree with Dave...at least on my 94. My gauge stopped working while replacing my injectors and glow plugs a while ago. After searching for the three coolant sensors and figuring out what they each do I have concluded the one by the IP controls the IP stuff, the large one on...
  8. international

    Push bumper Beef for cheap!

    I was JUST thinking about purchasing or building one of these. I want to incorporate a winch into it somehow without cutting a hole in the front push part. Wish it was closer.
  9. international

    Snap on or Craftsman tools?

    Craftsman except specialty tools. I'm a shade tree/hobby mechanic and have a hard time tracking a truck down when some of my over priced snap on, Mac or Matco tools break. Honestly, I must not be using my tools enough because all I break are craftsman and snap on ratchets. FYI all my local Sears...
  10. international

    Low throttle surging?

    My truck does the same thing. If you hold it at say 1200 rpm it will move on its own up to 1500 or so then back down to 1200 etc. figured my pump was on its way out.
  11. international

    Where to find this clip?

    Where can I get the clip in view "t"? Thanks!
  12. international

    So what did you do with your truck today?

    Replaced brake pads and shoes. Still fighting the fading pedal.
  13. international

    Fuel System Repair on the CHEAP?

    Cheap? I say drill a couple holes in the top of the rear tank. Clean the top of the tank and grease your drill bit. One for 5/16 return and one for the 3/8 supply. Cut the end of the supply hose so it wont suck to the bottom of the tank. Stick both hoses in about a foot, secure them with...
  14. international

    Factory 093 guys looking for Banks DP

    I live in Ohio...had to pay tax.
  15. international

    Factory 093 guys looking for Banks DP

    Just ordered one from Summit. $98.15 total. None in stock. They stated they order it from the manufacturer after you place your order. 1/31 delivery date.
See more

Latest posts

Forum statistics

Threads
91,306
Posts
1,130,034
Members
24,117
Latest member
olsen726

Members online

Total: 838 (members: 6, guests: 832)

Share this page

Top