Recent content by IDIJunkie

  1. IDIJunkie

    Oh $H!T Big Problem

    The timing was set to 9 deg about 4000 miles ago. The engine was running perfect when I pulled it into the shop. It wasn't knocking and didn't have any unusal sounds other than air bubbles coming out the radiator. It sat for 2 months and when I started it up at 15 out side temp it took about 1...
  2. IDIJunkie

    Oh $H!T Big Problem

    Thanks for the comments guys! Robert, I don't think that it could be cavitation, I've had Evans coolant in there for 40,000 miles. Mel, I haven't touched anything inside the engine untill now, it just turned 140,000 miles. Oldbull8 I might take you up on that, I have to drive to...
  3. IDIJunkie

    Oh $H!T Big Problem

    Well the head gasket job has just gotten a lot more involved! I just found a crack in the #7 cylinder :puke:-cuss. It has a small crack and a lot of scuffing on the cylinder wall. The #5 cylinder had 1 loose head bolt, and I think thats why it had lower compression then the rest. What I don't...
  4. IDIJunkie

    Head stud torque

    I just got some ARP head studs (thanks Gary & Russ for the part #;Sweet) and was wondering if these take the same torque as a head bolt of 100 lbs or something differant. I read that the studs require 5 torquings before the final torquing, is that right. Also is there anything I should before...
  5. IDIJunkie

    Head gasket install advice

    I am getting ready to install head gaskets this week and was wondering if anyone has any advice or tips to make things go easier, or anything that I should check while the heads are off. Any and all help is appreciated.
  6. IDIJunkie

    ATS elbow and downpipe

    Sean, The farthest that I have been into my engine was new valve cover gaskets, and the truck has 140,000 miles on it. Last year I did a moose pump, injectors, glow plugs (that you supplied me with :thanks:), innercooler, turbo upgrades, 5" exhaust, aluminum radiator, water pump, and valve...
  7. IDIJunkie

    Head bolt question?

    Russ do you have the 7 digit part numbers for the studs and washers? The numbers that Gary wrote I couldn't find anything in the ARP catalog.
  8. IDIJunkie

    Exhaust Tips

    Here is where I got mine. http://scheiddiesel.com/display_part/1816.php It's a 4" to 6" but I only paid $35 for mine at a farm show. Here are some pictures of it on the truck.
  9. IDIJunkie

    Head bolt question?

    Russ do you have the part numbers for the 6 point nuts, or are the 12 point nuts better?
  10. IDIJunkie

    Head bolt question?

    I found out that the powerstroke studs won't fit. Here is what ARP said in their email. The studs in that kit # are 12mm x 1.75 pitch. Eight of those studs are 6.625” long from end to end and twenty-eight of them are 6.850” long from end to end. Gary it looks like I will be using those...
  11. IDIJunkie

    Grill Blankets? Where can I get one?

    Sean here is a picture of mine. I've had it for about 4 years and it's a Lund cold front grille blanket but I think that they stoped making them. Here is the only place I know of some that looks like it, but they only go back to a 92...
  12. IDIJunkie

    Turbo oil drain gromet

    Anyone know where I can get a turbo oil drain gromet for the factory turbo? I went to ford the other day and they said that they quit making them and I was SOL:mad:.
  13. IDIJunkie

    ATS elbow and downpipe

    Sean, I'm still alive and kickin!! It's been about a while since I've been on. I got really busy with farm work and didn't have time to get on. I'll be on here alot more now as my truck is down with a blown head gasket. I don't do much posting since I'm on dial up and it takes so friken long to...
  14. IDIJunkie

    Head bolt question?

    Thanks! At least I know is might be possible. I am going to try to talk with the guy tomorrow and see what he has to say. BTW how much did you pay for the studs?
  15. IDIJunkie

    ATS elbow and downpipe

    I got them from http://www.jhdiesel.com/ats_exhaust.htm . They are really nice people. You can get just the outlet housing and downpipe from them no problem. You can use the outlet housing without the turbine housing. Talk with Anthony or Mike, if you want the whole kit it's part 73UKT, or if...
See more

Latest posts

Forum statistics

Threads
91,315
Posts
1,130,201
Members
24,121
Latest member
720Diesel

Members online

Total: 829 (members: 15, guests: 814)

Share this page

Top