What alls needed for a d60 swap

[83ford]

Ok I'm soon to do a d60 swap in my 86 and I have a d50 under it at the moment.ive got the stock f350 front springs and tie rods what else so I need and we're is a good cheep place to buy parts for it.it was 100 bucks for the ball joints at the parts store for the cheep ones.im sure I'll need something that I ain't got and would like to not spend a but load because I've got 2 other trucks that need stuff also.and will I need to shorten the drive shaft in the front end.thanks yall


Sent from my Iphone using Tapatalk

 

[79jasper]

Could've got spicer balljoints for cheaper.
You need the double Cardone F350 front shaft.

Sent from my SAMSUNG-SM-G890A using Tapatalk

 

[83ford]

Could've got spicer balljoints for cheaper.
You need the double Cardone F350 front shaft.

Sent from my SAMSUNG-SM-G890A using Tapatalk

The do what lol.i can probley get it from my boss since I got the transfer case and rear drive shaft from him outta f350


Sent from my Iphone using Tapatalk

 

[79jasper]

It's a wonky looking fella. Lol

Sent from my SAMSUNG-SM-G890A using Tapatalk

 

[83ford]

It's a wonky looking fella. Lol

Sent from my SAMSUNG-SM-G890A using Tapatalk

I figured lol hopefully I can find it at his place lol


Sent from my Iphone using Tapatalk

 

[79jasper]

It'll look like this. http://www.mdsdriveshaft.com/images/E9TZ-4A376-A.png

Sent from my SAMSUNG-SM-G890A using Tapatalk

 

[83ford]

Ok sweet thank ya also is there some kinda bar that comes off the frame to the axle


Sent from my Iphone using Tapatalk

 

[79jasper]

Trac bar.

Sent from my SAMSUNG-SM-G890A using Tapatalk

 

[83ford]

Ok how much are those lol


Sent from my Iphone using Tapatalk

 

[79jasper]

Depends if you go factory or aftermarket.

Sent from my SAMSUNG-SM-G890A using Tapatalk

 

[83ford]

We're can I get one cheep


Sent from my Iphone using Tapatalk

 

[riotwarrior]

D60 swap

Springs
Shocks 2" longer n f250 iirc
Pitman arm
Steering linkages
Track bar and track bar mount
Double cardan drive shaft

Cross member if it is a zf ...different than 250 cross member...dont know bout E4ODs sorry

That bout sums it up.

Hope uou have a BJ 60 not King pin

 

[83ford]

It is a ball joint and why a new cross me ever but I have a t19 and I've got the springs and tierod bars and stuff.so I need a new pitman are also?


Sent from my Iphone using Tapatalk

 

[riotwarrior]

It is a ball joint and why a new cross me ever but I have a t19 and I've got the springs and tierod bars and stuff.so I need a new pitman are also?


Sent from my Iphone using Tapatalk

If you have a ZF you need an f350 x member as it has a large droop for the front drive shaft due to increase in ride height. Same reason for double carda drive shaft.

As for T19 C6 or E4OD I personally couldnt say however I would imagine so.

Pitmam arm is longer for F350 so again this affects steering geometry.

Yer choice

You aksed I amswered

 

[mblaney]

Check the write up in my signature. I worried all these details and put all the answers in the thread about my swap.