Search results

  1. C

    2wd Leveling?

    So I've searched with no luck.. hate the raked stance of my 2wd obs and no time for a 4wd conversion yet, so want to see if anyone has used 2" coil spacers on a 2wd. Will camber be noticibly different? If so, what will it take to make it right?
  2. C

    u-joint issue killing me..

    I had a slight shake above 50 mph so I replaced both u joints with off the shelf ujoints. Got a little better but blew the rear out.. and then again.. learned my lesson and got Spicer ujoints and also had the driveshaft balanced. Now its super smooth. But heres my problem: I want to make sure...
  3. C

    oil pressure slow to build

    I just hooked my mechanical gauge back up and verified that for some reason its taking 1-3 secs to build oil pressure. The engine starts fine, runs for a couple seconds with no oil pressure and then shoots up to 45-50 psi. Is this normal? If not what's causing it? Maaaan I hope its nothing...
  4. C

    Flywheel question....

    So I located a flywheel inspection cover and went to install it. On one of the old bolts I noticed a little metal tab that says: Warning, LUK clutch and flywheel installed, only use LUK parts. That's great, but will a stock flywheel inspection cover fit without rubbing? No idea if they are...
  5. C

    glow plugs.. is this normal?

    So I've changed the whole glow system once and the controller 3 times, went through 2 cheap controllers before I bought a motorcraft controller. That's all a long story, but anyway, since I installed the motorcraft controller the wait to start light comes on and stays on for a good amount of...
  6. C

    Wanted: zf-5 flywheel inspection cover

    Looking to buy a flywheel inspection cover for my '92 f250 7.3 idi zf-5. Still no luck finding one locally. Ford said they discontinued them. Anyone have one to sell?
  7. C

    Not sure my front leaf springs are doing anything at all anymore..

    I have almost no space between my axle and bump stop, the front end sags and I'm hoping that's what's throwing my camber off. How have you guys fixed this? Have the leafsprings re-bent? Lift kits? Donor trucks? Looking for something that works and will last but of course the cheaper the...
  8. C

    sterling 10.25 axle seal

    Started work on my brakes and noticed both axle seals had let loose. The hubs are off but I can't seem to get the old axle seals out of the hub!! What's the trick??? Everything I've read says to just remove them. Thought I'd stop before I break something
  9. C

    looking for a pic of a zf-5 flywheel dust cover (or for sale!)

    Trying to find a flywheel cover for my F250 and having a pic would really help. Cant seem to find a good google pic. Or if anyone has one they can sell that would also help! Haha
  10. C

    WTB: flywheel cover for 7.3 idi with zf-5 trans

    Looking for a flywheel cover for my 1992 f250 7.3 idi with the zf-5 trans. My truck was sold to me without it so just looking for a replacement. Anyone have a spare??
  11. C

    Power wires to glow plug controller get VERY hot, new controller and wiring harness

    Stumped.. when i bought my truck (92 F250 7.3 IDI) the glow plugs didn't work at all. I replaced all 8 glow plugs with motorcraft, then replaced the controller. In the process I noticed that the ground for the old controller was never hooked up. I finished installing the new controller and it...
  12. C

    WTB 7.3 IDI Oil Cooler

    I'm looking for an oil cooler for my 1992 F250 IDI. I lost oil pressure and when I took my oil cooler off I found the regulator valve and spring are gone!! I'm hoping to find one within driving distance but shipping's an options too. Thanks! Trevor Wichita, KS
  13. C

    Anyone fix a stuck oil regulator valve or am i stuck with pulling my oil cooler?

    So my 7.3 idi started getting low oil pressure at idle. I hooked up a manual gauge and confirmed it. I did some research and suspected my oil pressure regulator valve is stuck open in my filter adapter. So I tried to follow some instructions to try to close it manually and misunderstood what was...

Latest posts

Forum statistics

Threads
91,292
Posts
1,129,832
Members
24,106
Latest member
lewisstevey7

Members online

Total: 667 (members: 5, guests: 662)

Share this page

Top