was wondering if anyone had any tips for removing the clutch master cylinder from the firewall. do you just turn it or are the tabs locked in notches and you have to push it in first? tried turning it by hand and it wouldnt budge.
Hi, i was researching the adrenaline hpop and was told that i can not use this pump with the edge juice with attitude. has anyone done this or know what problems can happen if i do this
ok cuz the truck runs fine power wise so thats wats makin me think its not the high pressure oil pump cuz then it would have a loss of power for how much its leakin right? cuz it is leakin bad
ok im not in the greatest mood so ill get to the point
2000 F-350 175,000 miles
big oil leak and could see a river of black in the valley going from the front of the motor running to the back and down the bellhousing
took the fuel filter bowl off and whole passenger side was wet..high...
so i am about to get a whicked wheel for my turbo and had plans to get a different ported turbine housing. was wondering if i should do this or spend the extra to get a ball bearing turbo. im also gonna get biggboost..didnt know if im gonna blow the turbo up from high boost with all these mods
i got a buddy whos got a 92 460 fuel injected and he is switching it over to carb. we have the intake off of an earlier motor that was carb and the intake sits to low in the valley. does he have to use the heads off the earlier motor or is there an intake he can buy that will fit the newer motor
i was wondering if there is anything special or difficult about adjusting the valve lash on the 7.3 . just wanting some tips or warnings about things to take off or watch out for
ok thanks guys i think i have heard enough to know its time to pull the tranny and i can get a whole truck with working tranny for 500 so i think im gonna go that route
no it still drove and worked but shifted funny from water in fluid because i have a leak in my input shaft seal. it has not wated to go forward when the fluid was right at the low mark on the dipstick and i would add a quart and it would work again but now it is full and still not going forward
what are you wanting to know the internals for? it would take pages to truly explain how these pumps work. is there a certain part you need to replace? the tolerances on injection pumps are so tight that its not smart to just take one apart on your workbench. if you have ever seen inside a...
ok so heres wat my 1990 E40d (with as far as i know has 240,000 miles on it) is doin. it will go in park reverse and neutral just fine but all the forward gears sound like neutral and doesnt have any forward movement. i did go through a creek with it but had the fluid and filter changed. i have...
ok heres the deal truck wont start because its gettin air in the fuel. the fuel heater leaks on the lift pump. Is it replaceable? the connector is cracked but is that supposed to hold fuel from leaking? because it is bubbling up through the metal tab. if not replaceable could i plug it up somehow?
ok so my truck has been gettin harder to start and i thought the batteries were gettin weak. this morning it started and ran rough and i gave it some fuel and it didnt rev up and it ran a little and then shut off. i tried starting it and it didnt even try to start. im gettin fuel to the...
ok so iv been lookin for a dana 60 to do a swap in my truck. iv been lookin for about a month now and it seems like its much easier to find an axle from a dually. can i just take the hub extender out and put a new hub in from a srw axle and everything be the same? im tryin to find an axle for...
so i was wonderin if the 7.3 has an oil cooler. it looks like there is right before the oil filter but i was just wonderin wat that was and if there are gaskets and watnot because that is leakin along with every other thing on this truck it seems like lol
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.