Forums
New posts
Search forums
What's new
New posts
New resources
Latest activity
Resources
Latest reviews
Search resources
Members
Registered members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
Registered members
Current visitors
Menu
Log in
Register
Install the app
Install
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Mt_Man
Full Access Member
·
From
Portland, Oregon
Joined
Nov 12, 2017
Last seen
Yesterday at 9:23 PM
Posts
208
Reaction score
85
Points
28
Find
Find content
Find all content by Mt_Man
Find all threads by Mt_Man
Latest activity
Postings
About
Mt_Man
replied to the thread
Waste Transformer Oil
.
Second burn was of 50:50 silicone oil and jet a. Blended great and seemed to have 50% less white ash that formed on the outside of the...
Jan 18, 2023
Mt_Man
replied to the thread
Waste Transformer Oil
.
Silicone oil burn test. Dipped a paper towel in about half way and squeezed it slightly so it would not drip to much. You can see the...
Jan 18, 2023
Mt_Man
replied to the thread
Kerosene is cheaper than diesel. How much can I add to WMO?
.
1qt cheap motor oil per 50gal is what I have been told for kerosene type fuels. I go a little extra lube just to be safe. Old heater oil...
Jan 17, 2023
Mt_Man
reacted to
Far Right's post
in the thread
How much crud should I be getting in my centrifuge
with
Like
.
I’m sucking it from a drop tube that picks up from front bottom through the 2” hole
Jan 11, 2023
Mt_Man
replied to the thread
How much crud should I be getting in my centrifuge
.
Yep sounds like it's pretty clean and diminishing returns. Are you sucking front the bottom and putting back in the top for your fuge...
Jan 9, 2023
Mt_Man
reacted to
Far Right's post
in the thread
How much crud should I be getting in my centrifuge
with
Like
.
Ok so ran it at 90deg c through my fuge for 6 hrs. I did get more out but it was so little extra that I dont see the Benifits in going...
Jan 9, 2023
Mt_Man
reacted to
Far Right's post
in the thread
How much crud should I be getting in my centrifuge
with
Like
.
Ok thanks mate, I’ll turn the temp up a bit today n run it In circuit as I modded my drum yesterday, see if I can get something out of...
Jan 9, 2023
Mt_Man
replied to the thread
How much crud should I be getting in my centrifuge
.
Damn that is spendy for a fuge. I think you are on the right track. So if you have a 100L container and 3x means 300L worth of...
Jan 8, 2023
Mt_Man
reacted to
Far Right's post
in the thread
How much crud should I be getting in my centrifuge
with
Like
.
Yeah ok mate thanks, so 3x what L per min my fuge is will equal 1 pass per L of oil, so say 100L needs to pass through at a rate of 300L...
Jan 8, 2023
Mt_Man
replied to the thread
How much crud should I be getting in my centrifuge
.
Oh and if the contaminate is the same or close to the specific gravity of the fuel the a fuge won't get it out but a filter might.
Jan 7, 2023
Mt_Man
replied to the thread
How much crud should I be getting in my centrifuge
.
Yep always good to have a QC filter. Sounds like you have very clean oil. Nice. I have been told that when recirculating...
Jan 7, 2023
Mt_Man
reacted to
Far Right's post
in the thread
How much crud should I be getting in my centrifuge
with
Like
.
Ambient temp 30deg c Oil temp 60deg c (heated) Thinned with jet fuel 70L wmo 40L jet fuel 5 passes n nothing to speak of, I have been...
Jan 7, 2023
Mt_Man
reacted to
Far Right's post
in the thread
How much crud should I be getting in my centrifuge
with
Like
.
When these fuges are on a vehicle or stationary engine filtering the engine oil they contain a paper filter element, I wonder if using...
Jan 7, 2023
Mt_Man
reacted to
Far Right's post
in the thread
How much crud should I be getting in my centrifuge
with
Like
.
Yeah ok so the paper will not trap more crud, the instructions with my fuge say not to heat oil more than 60-70degc cause the pump seals...
Jan 7, 2023
Mt_Man
reacted to
u2slow's post
in the thread
How much crud should I be getting in my centrifuge
with
Like
.
We centrifuge lube oil at work; engines are fitted with them.... More like 70-90°c and no thinning/dilution. Other sites, the...
Jan 7, 2023
Loading…
Loading…
Latest posts
"Tank" my 91 Crew Cab Dually
Latest: catbird7
25 minutes ago
6.9L IH & 7.3L IDI Diesels
Jesus Freak's WMO IP thread
Latest: Jesus Freak
43 minutes ago
6.9L IH & 7.3L IDI Diesels
WTB: Wastegated Banks Sidewinder Parts for Ford IDI
Latest: Minuteman96
Today at 4:20 PM
Wanted
96 First Powerstroke
Latest: captain720
Today at 3:17 PM
7.3L Powerstroke Diesels
B
Specialty Tools Needed for 7.3 Rebuild?
Latest: bulletpruf
Today at 3:03 PM
6.9L IH & 7.3L IDI Diesels
Forum statistics
Threads
90,112
Posts
1,106,513
Members
23,122
Latest member
BigRich
Members online
perith42
trackspeeder
catbird7
captain720
Black dawg
Share this page
Facebook
Twitter
Reddit
Pinterest
Tumblr
WhatsApp
Email
Share
Link
Members
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top