Recent content by shocktrooper

  1. S

    6.9 pinging/tapping noise

    Hey guys, so I have a 6.9. Just did the head gasket put 7.3 heads on with new injectors and timed my ip pump. Had the truck on a dyno and pulled just u get 400 ft lb and always has lots of power. it is also a non turbo. Wired thing is when I put my foot In it I get a pinging/taping noise. It's...
  2. S

    85 6.9 pulling 130 hp and 380 ftLb N/A good or bad?

    Hey guys i did my first IDI rebuild a while back and used 7.3 heads on a 6.9 idi with stock injectors and pump, pump is turned up a bit and timing set. i pulled 380 Ft-lb on my schools dyno from a dead stop to 65. Are those decent numbers or average? thanks guys
  3. S

    ZF-5 on a 6.9 idi

    Hey guys. Been looking around trying to get some info on a swap from my c6 to a zf5. The truck is a 85 f250 4x4 with Cruze control c6 automatic with 4:10 gears. I can pick up a tranny and t case for 200 bucks. I am just wondering what else I may need to complete the swap ( like cross member...
  4. S

    6.9 idi Garrett turbo

    Cool I Appreciate Itwvdirtroad! Thanks!
  5. S

    6.9 idi Garrett turbo

    I'm not trying. To hurt you in any way. I've rebuilt a few powerstroke turbos and never had a problem. bi shaft play in the turbo I just want to replace the inlet gasket just to make sure I do t have a runaway.
  6. S

    6.9 idi Garrett turbo

    On the housing it is imprinted A/R.70 m43 B.O Garrett. And the tag is 472553-0000
  7. S

    6.9 idi Garrett turbo

    The impellers are balanced already. You don't have to rebalance them if you take them apart.
  8. S

    6.9 idi Garrett turbo

    Ok cool when I get home I'll take a few pics o everything and post them here.
  9. S

    6.9 idi Garrett turbo

    I have no idea I took it off a motor a guy gave me for payment. The exuast hoisting for the down pipe is stamped ATS and the boost side is Garrett. I'm just looking for a new gasket or o ring set for it so take sure it doesn't leak on me befor I put it on my pickup.
  10. S

    6.9 idi Garrett turbo

    Hey guys I picked up a Garrett turbo off a 6.9 with the ATS exuast housing. Great looking turbo but I want to put new gaskets in it since its on my work bench already. I just can't seam to find a deal kit for it. Anybody have a seal kit number or where I could find one. Thanks.
  11. S

    7.3 Heads on a 6.9

    I had a few people tell me 7.3 heads would not work on a 6.9. But the guys on here gave me the part numbers for the 8 longer head bolts and washers to take up the space from 1/2 inch to 7/16. Then I took out the plugs in the water passages for cooling. And the 7.3 heads have stronger...
  12. S

    7.3 Heads on a 6.9

    Well after a month of fighting the post office to get my parts finnaly got the truck up and running! Runs damn good with those 7.3 heads on it and the convention is successful.
  13. S

    7.3 Heads on a 6.9

    Sweet thanks!!
  14. S

    7.3 Heads on a 6.9

    Yea I've been looking for longer 7/16 studs for those holes. Can't find any longer though. If you guys know where to find some let me know. Been on arp and everything nobody has longer than 6 inch. It requires a 7 for those 4 holes on each head.
  15. S

    7.3 Heads on a 6.9

    Have not put them on just yet need to get dowel pins. I was thinking the same thing but at 85 ft lbs. I didn't know if I was gonna need stronger. The ones that came out where grade 8. But now that you have said that I might go a little higher.
See more

Latest posts

Forum statistics

Threads
91,305
Posts
1,130,002
Members
24,115
Latest member
Tyler9828

Members online

Total: 708 (members: 5, guests: 703)

Share this page

Top