Recent content by gotdiesel?

  1. gotdiesel?

    Grease Zirks

    That's a fact. One fitting on each tie rod. Don't worry though, if you're grease crazy like me, you'll soon have the opportunity to replace u-joint by the armful(like me!! :mad: :puke: ) with greasable aftermarket units.
  2. gotdiesel?

    guess the truck.....

    I'd guess an old Detroit, maybe in a B model?
  3. gotdiesel?

    911 members support list info thread

    Josh Rochester, NH Cell-603-817-9244(leave message, I usually don't answer unknown numbers) Bumper pull or gooseneck Have access to 24'+4' g/n flatbed, Small shop at my parents with fair tool selection + welder and torches My best friend has a small dairy farm, so some pasture could be...
  4. gotdiesel?

    What'cha towing?

    Here's mine
  5. gotdiesel?

    Big problem with Muffler delete!!!!

    Okay, maybe someone else has had this problem. I installed the muffler elimination kit from Geno's about 3 weeks ago (about a week after pulling the silencer ring). Since then, whenever I'm just tooling around town, on the highway or pretty much anywhere else, I just keep pushing down on the...
  6. gotdiesel?

    Tire size

    I decided to go with the Nitto Terra Grapplers (295/70/17), ordered them 2 weeks ago and they're backordered. should see them in 3-4 more weeks.
  7. gotdiesel?

    Talk me down fellas!

    I agree with Agnem; use the force use the force of a CTD to propel your *** like it's never been propelled before :rotflmao :rotflmao :rotflmao :rotflmao :rotflmao
  8. gotdiesel?

    Tensioner

    You know its funny, my buddy's vaccuum pump took a :number2 right before his idler did too. I think the pulley is held on with a TORX headed bolt, for some reason, a number 27 TORX sticks out in my mind. I turn wrenches on a lot of things, from hay balers to tractors to Harleys to fuel pumps...
  9. gotdiesel?

    Tensioner

    jharvey, I did the tensioner on my buddy's '96 F350 about 5 or 6 months ago, but it should be about the same. If I remember, the tensioner and pulley were about $100 @ NAPA and throw in another $45 I think for the belt. Chances are, if the bushing is gone in the pulley, you've chewed...
  10. gotdiesel?

    Tire size

    I'd be staying with the stock steelies for now. So things will probably work out just fine
  11. gotdiesel?

    Tire size

    So, to put the 315 on my truck, I should be able to put the 2" spacer in the front to make room for full articulation and be fine right? Padiesel was right, the deal on the 315's is pretty good and I think they would look pretty damn good on my redneck limousine!!!!
  12. gotdiesel?

    New to forum- a few questions

    Good lookin' truck, jdw. I'm not much of a ford guy, since I found the power of the goat, but I believe the 1990's had the monobeam IFS. I have seen many of these trucks, gas and diesel, which get weak spring disease. The way the front suspension is set up, weak springs throw the camber all...
  13. gotdiesel?

    Serviceing..............

    I have to agree with Muddy. My '03 is a snap to service. 15 minutes start to finish, 20 if the oil isn't nice and hot. Granted, I got a lift in the shop at work, but I don't see it being much worse on a jack. Just my $.02
  14. gotdiesel?

    How do you get old rusty exhaust pipes loose?

    You will not be sorry. PB is the best stuff in the world. I don't know what relevance the styrofoam cup test has, but that's what sold me!!!!
  15. gotdiesel?

    New DURAMAX owner

    Advice if you do sell it and buy a Ford. Drive the Ford off of a bridge, take the insurance check and buy a dodge!!!! Sorry, I just had to get mine in too. Good luck with the new ride and welcome to OB
See more

Latest posts

Forum statistics

Threads
91,304
Posts
1,129,986
Members
24,111
Latest member
Lance

Members online

Total: 590 (members: 5, guests: 585)

Share this page

Top