Search results

  1. N

    Obs blue 40/20/40 cab part out

    No rips just need a good cleaning. Out of my extended cab also have the rear bench seat if anyone is also interesting. $350 Tilt steering column $175 Still have the full blue interior and will be parting it out. Dash pad is cracked I am willing to ship some stuff
  2. N

    94 F250 IDI turbo 4x4 part out

    Bed is sold, Motor is sold, D60 With new Moog connecting tie rod, adjusting sleeve and tie rod for the pitman arm still in the box. Track bar with poly bushings and the bracket. New Moog ball joints and new calipers 5000 miles ago. $700 E4OD 4x4 trans with magtech pan. Trans was rebuilt by...
  3. N

    94 F250 IDI turbo 4x4 part out

    94 F250 IDI turbo 4x4 All the info is in my old thread, I'm willing to ship some stuff truck has a blue Lariat interior. I'm going to snap more pictures this weekend.
  4. N

    94 F250 IDI turbo 4x4

    Figured I'd give you guys here a shot at her since most of you have the ability and time to fix her if you want a project. If not they I will part her out and give this site first crack at parts. I just don't have time for her anymore, Bought a new truck awhile ago and as much as I want to...
  5. N

    Frame rust

    long story short, how much rust is to much? She was in an accident and not sure if I should even attempt to fix or just part her out. truck has had a plow on it since new but have not plowed with her in about 7 years.
  6. N

    Might be the end of my truck

    Well I think my truck has met its end. The jeep tried to turn in front of me and caught me right in the corner. It happen in the spring and I just had her put in the garage as took the time to see what would happen with her. They totaled her out but let me keep her. Just not sure she is worth...
  7. N

    D50 axle shafts with new u joints

    Have a set of D50 axles with new splicer U joints. Went D60 so I didn't install them. Located in NJ but I can ship. $150 obo plus shipping
  8. N

    Need a radiator support

    Well a little while ago I had an car accident with my truck and now I'm getting around to fixing it. I need a bunch of parts but I know the hard one is a new rad support. I got a new Jeff's bronco graveyard catalog and it has a core support for a 92-94 diesel. But I was always under the...
  9. N

    Radiator Cap Confusion

    I servicing my cooling system and installing a new thermostat. I noticed that my radiator cap is starting to leak and the rubber in it is starting to crack up. Its a Ford radiator cap 16lb. But NAPA says I should have a 13lb cap. which is the right cap for the IDI? Also can I trust an...
  10. N

    250 driveshaft vs 350 driveshaft?

    I did my D6o swap in the beginning for the year but never put a front driveshaft in it. Many have told me that my 250 shaft will work but why do 350 have the CV joint? I plow with my truck so which shaft should I go with? Also if I do get the 350 shaft what is the part number for the T-case...
  11. N

    steel or plastic drum?

    I'm going to go pic up a 55 gallon drum this week. so what does everyone prefer? steel or plastic?
  12. N

    D50 springs with new bushings

    Put a D60 in my truck. I put new rubber bushings in the springs about 10k miles ago and an add a leaf put in when I got them re-arched at a spring company. $75 obo located in North NJ.
  13. N

    Vacuum pump pulely?

    I tweeked my vacuum pump pulley when I pulled it off the old pump. Where can I get a new vacuum pump pulley?
  14. N

    D60 finally is in...

    A few weeks ago I put in an D60 I got out of a 95 F350. put new ball joints and brakes on it while it was on the jack stands. repacked the bearings and new U-joints in axle shafts. After I gave her an alignment good enough to just get her to the tire shop I took her for a test run. The ride was...
  15. N

    What Vacuum pump?

    Need a new vacuum pump. the last one I put in was a rebuild and lasted about 2 years. Is there a superior brand to go with? Or should I just bite the bullet and buy a motorcraft one?
  16. N

    a/c clutch seize up?

    Well leave it to me to finally address my ac woes. Last year in September my ac stopped working. Well today I found the leak and fixed it. Pulled a vacuum for about 30 minutes no problems. Started adding 134a with the truck running. The compressor kicked on and then promptly seized up. I shut...
  17. N

    D60 question

    I have a D60 out of a 95 F350 going into my truck. I just started taking it apart to put new ball joints and U joints in it. My question is what is the size of the bottom ball joint nut? is it metric or standard? 1 1/4" socked is to small but I don't want to buy a bigger socket set until I know...
  18. N

    OD light flashing because of overheating?

    I was pulling a trailer with a mini excavator today. while climbing a long grade after sitting in stop and go traffic on a highway the OD light started flashing. truck shifted fine no hard limp mode shifts. I pulled over to check it out and found no leaks. After I arrived at my friends house to...
  19. N

    vacuum pump died

    In a nutshell my vacuum pump is about 3 years old and it won't pull more then 15" of vacuum. it was a rebuilt replacement pump but I do not remember what company it is from. What is the best rebuild to go with? I'm looking to just order one from rockauto.com since they seem to have the best...
  20. N

    trans dipstick for my 94 idi turbo

    Well I need a dipstick for my truck, not the tube just the stick! Cousin borrowed the truck and decided to be a nice guy and check the fluids. turns out he must have missed the tube when he went to put it back and its gone somewhere on I95.
  21. N

    D60 driveshaft?

    Ok tonight i picked up a D60 out of a 95 F350 with springs and everything. Now some people including the guy i bought the D60 from says i can use my 250 driveshaft. some don't. What is the difference between the 250 and 350 driveshaft?
  22. N

    dana 60 parts?

    I am thinking about swaping a D60 into my F250. I can get a Dana out of a 95 F350, after reading up on here about them I still have a few ?. the brakes on my d50 ttb are a month old will they swap over to the 95 d60? Also besides the spindles is there any difference between the 95 D60 and the...
  23. N

    fan shroud needed

    had an issue and the fan shroud got mangled beyond saving. need a fan shroud for my 94 IDI asap
  24. N

    dipstick tube discontinued?

    Ok went to ford to order a new engine dipstick tube and new trans dipstick tube. after trying to convince the kid behind the counter at the dealership i didn't have a powerstroke we get the order placed and i pay for it. he says should be a few days. Got a call the next day that ford...
  25. N

    D60 swap questions.

    ok i fragged my front D50 bad. I tried to do a quick serch about D60 swaps but didn't find a ton on it so I have a few questions. What is the easiest way to just swap a 60 in? if i get the D60 and the springs and driveshaft from a F-350 will it just all bolt in? I'm pretty much getting tired of...

Latest posts

Forum statistics

Threads
91,310
Posts
1,130,149
Members
24,120
Latest member
SixFourShanks08

Members online

Total: 602 (members: 13, guests: 589)

Share this page

Top