Search results

  1. 9

    What torque for the waterpump bolts

    I'm replacing one away from home and don't have my manual with me.
  2. 9

    SMF flywheel that uses stock DMF pressure plate

    Do you guys know if someone sells a single mass flywheel that accepts the stock DMF 6 bolt pressure plate and 11" clutch? I just bought a SMF to replace my Lucky modded flywheel, but its for a larger clutch with an 8 bolt pressure plate.
  3. 9

    WTB: Complete 6.9/7.3 IDI Turbo kit

    As the title says.
  4. 9

    Preparing to filter some WMO....

    I use the cim-tek spin-on filters, a 110v 13gpm transfer pump, a 55 gallon drum, and this tank heater http://www.jeffersequine.com/bucket-heater/camid/EQU/cp/AN-B1/ The heater helps vastly with the filtering speed and filter life. I removed the heat shield and it fits right into the 2" drum...
  5. 9

    Pyro necessary on a stock truck?

    I have a 97 that I will be towing no more than 7000 lbs with. It is bone stock so is there no need for a pyro gauge? I was planning on at least doing a 3" downpipe with a 4" exhaust.
  6. 9

    Worth it to run two fuel filters?

    Then what do you do about a clogged fuel filter. Replace all of them?
  7. 9

    Worth it to run two fuel filters?

    My 87 has a racor water separator in place of the stock one. I believe it needs a new filter. Should I replace the filter in it or just leave it out and let the main fuel filter do it all? For what its worth, I'm running prefiltered WMO through it as well.
  8. 9

    Starter doesn't stop cranking

    Figured out the ignition switch on top of the column was just out of adjustment. Now I have only 8 volts at the orange wire when in the ON position, and my starter should stay off.
  9. 9

    Starter doesn't stop cranking

    Right now it is reading 11.6v at the orange wire with the ignition in the ON position. I forgot to mention that this problem is intermittent and sometimes the truck will act normally.
  10. 9

    Starter doesn't stop cranking

    Thanks for the suggestion. Are you talking about the ignition switch thats on the top of the column that the lock cylinder rod goes to?
  11. 9

    Starter doesn't stop cranking

    When I turn the truck to the on position the starter cranks and will continue spinning while the truck is running. It looks like the orange wire that goes to the top of the starter solenoid has continuous 12v, causing this to happen. Is this a short somewhere or could it possibly be a bad...
  12. 9

    CL deal in central CA

    http://slo.craigslist.org/cto/1863735034.html I dont know what kind of offer this kid is looking for but for all the parts on there it could be a good deal.
  13. 9

    Ebay Intercooler

    Thats a really good deal. I found a kit similar to that and having all the pre-bent pipes was really helpful. I was able to cut and weld the pipes into something that fit my truck and only had to buy a short piece of straight pipe from an exhaust shop. My truck has a much smaller intercooler...
  14. 9

    Glowplugs on while starting

    My truck has the glow plug system hooked up to a button on my dash. Is there any reason I shouldn't keep holding the plugs on while I am turning over the truck? Do the trucks work like that from the factory with the plugs staying on while starting?
  15. 9

    first roadtrip running SVO!!

    Did you run a heat exchanger on it? Congrats on the trip, I love that feeling of traveling on little dime.
  16. 9

    On the road again!!!!

    Do you have any idea what it weighs? I bet its pretty quick in that lighter scout.
  17. 9

    Show off your WMO/WVO filtration setups

    I've been using it for about half a year now. It pumps 100% WATF no problem without filters on it. It struggled when the filter were on, mostly because they were clogging so fast. Now I started heating my oil and it pumps it through the filters a lot easier.
  18. 9

    Show off your WMO/WVO filtration setups

    10 micron into a 2 micron.
  19. 9

    Ladies and gentlemen! She's gorgious

    Im just playin with ya. Its a good way to spruce up the engine bay.
  20. 9

    Ladies and gentlemen! She's gorgious

    Is that the underhood of a honda civic?
  21. 9

    Changing clutch. Removing transmission questions.

    the zf-5 is a heavy son of a b. I found it impossible to maneuver around without the help of a transmission jack.
  22. 9

    Proud of the old girl

    I can hear the banjo playing... Nice looking truck you've got.
  23. 9

    Hurry and buy this 6.9

    I never understood the need to post on a thread that someone has a sent someone a pm.
  24. 9

    WMO

    I'm mixing roughly 75% watf/wmo and it runs great. I run a small amount of rug to thin it. I filter through a couple cimtek spin-on filters down to 2 micron. I just got a $33 1000 watt 110v bucket heater from jeffersequine.com to heat up the oil in the drum before I filter it. I will never go...
  25. 9

    IDI Torque Screw Adjustment

    I messed with the screw above the fuel lines which is at a 90* angle to the pump. It looks similar to your guys' torque screw except for the angle. It ended up dropping my idle way down to almost 500rpm when i screwed it out and my cold idle kick up stopped coming on.

Latest posts

Forum statistics

Threads
91,333
Posts
1,130,532
Members
24,136
Latest member
m2rtin

Members online

Total: 818 (members: 9, guests: 809)

Share this page

Top