Recent content by Optikalillushun
-
O
Starter for 94 turbo diesel 7.3
Cpaddicts had dash pads. 92/93 was dark gray, 94-97 was opal. Color change for interior seems to be 94 my except tan that im aware of. Yes im back from the dead.- Optikalillushun
- Post #49
- Forum: 6.9L IH & 7.3L IDI Diesels
-
O
What tires are decent for mud, snow and towing?
General Grabber AT2...wear like iron, good traction (similiar tread pattern to bfg at)...- Optikalillushun
- Post #6
- Forum: 6.9L IH & 7.3L IDI Diesels
-
O
and the process starts again!!!
That old truck looked killer...a brick in that config would be sweet...so would a slant...- Optikalillushun
- Post #9
- Forum: 6.9L IH & 7.3L IDI Diesels
-
O
and the process starts again!!!
Gotta link to the old build or pics of the old truck? Seems like a neat project.- Optikalillushun
- Post #6
- Forum: 6.9L IH & 7.3L IDI Diesels
-
O
1993 dana 60
Another option is using a 70s F150 style radius arm front suspension...i forget who but u can get weld on C wedges and spacers for radius arms...might be a bit less fab in the end and a better ride. It'd be similiar to isntalling a 70s F150 axle in any TTB F150 or Bronco and its fairly simple.- Optikalillushun
- Post #5
- Forum: 6.9L IH & 7.3L IDI Diesels
-
O
Vent/wing window removal
Got one this morning, was just as ya said thanks again. Got lucky n the door was off the truck and no door panel with the window down already...like a sign it was for me...lol.- Optikalillushun
- Post #4
- Forum: 6.9L IH & 7.3L IDI Diesels
-
O
Vent/wing window removal
Not hard, thanks!- Optikalillushun
- Post #3
- Forum: 6.9L IH & 7.3L IDI Diesels
-
O
Vent/wing window removal
For a 93 f150 but applies to these trucks...how does one go about removing the vent/wing window assembly? One the only things i havent messed with on my junk yet, and i need to replace it due to frame damage from an attempted vehicle theft.- Optikalillushun
- Thread
- Replies: 4
- Forum: 6.9L IH & 7.3L IDI Diesels
-
O
I-beam bushing question
Thats how i change most bushings like that (also leaf springs) much easier, cleaner, safer and quicker of u get the hang of it. I opted for an air hammer to remove the outer shell...beware those some bushings reuse that outer shell...- Optikalillushun
- Post #11
- Forum: 6.9L IH & 7.3L IDI Diesels
-
O
interior parts compatibility
Pretty much have to stay within the gen (92-96/7), mostly everuthing from the front cab will interchange with any 92-96/7 truck or bronco just be aware of some minors differences in the dash trim, interior color and seats. Seat from a reg cab will work in either seat in a crew cab, things like...- Optikalillushun
- Post #3
- Forum: 6.9L IH & 7.3L IDI Diesels
-
O
Messed up vacuum pump pulley
advanced or autozone i dont remember which has new pulleys for about $50. U need a special puller which is like $150-200...i just bought a new one...- Optikalillushun
- Post #16
- Forum: 6.9L IH & 7.3L IDI Diesels
-
O
Another friend bought a 6.0
Got the top end torn down to do the EGR delete and new oil cooler. Wasnt bad at all, actually besides from things being a little tight in places its easy. Got the new oil cooler installed, gunna finish it up tomorrow...only hurdle to cross now is the up pipe for the EGR delete.- Optikalillushun
- Post #5
- Forum: 6.0L Powerstroke Diesels
-
O
What is the difference?
92+ all F250s had dana 50s,- Optikalillushun
- Post #15
- Forum: 6.9L IH & 7.3L IDI Diesels
-
O
supercharged IDI
Thats seewalkersea on here...- Optikalillushun
- Post #3
- Forum: 6.9L IH & 7.3L IDI Diesels
-
O
Return lines leaking STILL
I replaced all the rubber in the fuel system for assurance last year (return lines, olives, fuel lines, etc) back as far as i could go. Perhaps restriction somewhere could be why i dont know. Today once i am done with my errands im gunna give a try at installing a new set of o-rings (the...- Optikalillushun
- Post #19
- Forum: 6.9L IH & 7.3L IDI Diesels
