Search results

  1. 94f350

    Jesus Freak's WMO tow truck

    I hope you don't smoke cigarettes
  2. 94f350

    Linking gas tanks

    So I had an idea and I didn't know if it would work or if anyone else had tried it. So on my truck my Fuel selector valve doesn't work like on many other obs ford's. I was thinking if I welded a couple ports and connected hoses to link the tanks together if it would work as a way to bypass the...
  3. 94f350

    Mechanical shutoff

    It doesn't really look too complicated so I don't think it'd cost that much aside from being an uncommon part.
  4. 94f350

    Fuel shutoff solenoid wiring

    Will do, thank you
  5. 94f350

    Fuel shutoff solenoid wiring

    Just #3 I think. I had to pull the picture from Google because I'm away from home right now and can't get a picture under the hood.
  6. 94f350

    Fuel shutoff solenoid wiring

    I need the copper ground wires
  7. 94f350

    Mechanical shutoff

    If there was a blueprint of this I'd definitely be willing to make one.
  8. 94f350

    Fuel shutoff solenoid wiring

    Does anyone know where I could get the copper bands for the FSS on the injection pump. I lost mine while working on it and tried African engineering some splice connectors and I had no luck.
  9. 94f350

    Knocking after injector change

    I had a similar issue on my truck, started out with a really bad leak out the injectors because I replaced the o rings incorrectly, said "**** it" for a few days and one day I started it up after running it for a few hours and it knocked like a ************ until I shut it off, then ran fine, I...
  10. 94f350

    Backpressure on exhaust

    I was thinking about straight piping my truck but I don't want to make it any slower than it already is. Does anyone know if an idi needs exhaust backpressure or is that more of a gasser thing?
  11. 94f350

    Knocking engine

    It happened twice and I haven't started it since because I'm a little scared of what might happen
  12. 94f350

    Knocking engine

    I didn't check for low compression but when the starter is cranking all cylinders are an even crank except for one which goes really fast. Sounds kinda like it's firing but it's not.
  13. 94f350

    Knocking engine

    I let it run for a minute and when I tried to give it throttle it knocked harder, didn't change after it idled down.
  14. 94f350

    Knocking engine

    But that doesn't explain the weird compression issue, I dodon'understand how that can happen and then go away
  15. 94f350

    Knocking engine

    Also, I don't understand how the engine would run good after it had just knocked like crazy. I don't understand what could've changed. I shut it off again after it was running good and I went to start it like an hour later and knocked, shut it off, turned it back on again and it ran fine. It...
  16. 94f350

    Knocking engine

    Every cylinder had an even crank except for one which kinda sounded like it was firing but It wasn't, you could tell there was zero resistance on the starter.
  17. 94f350

    Knocking engine

    IIf it held a valve open then wouldn't I probably have bottom end damage from the piston hitting the valve?
  18. 94f350

    Knocking engine

    But that wouldn't explain the weird compression issue though, also it was a very heavy knock, kinda sounded like rod knock
  19. 94f350

    Knocking engine

    Well it had to have been a valve open because it was cranking like one cylinder had zero compression. I can't think of anything else that could cause that randomly.
  20. 94f350

    Knocking engine

    So if my valve was held open do you think we're talking major engine damage or could I walk away from this?
  21. 94f350

    Knocking engine

    So I think I have a bent pushrod in my engine (7.3 idi NA) because when I went to start it up the other day one cylinder had zero compression when it was cranking and when it started it knocked really bad. I shut it off and a few minutes later I went to start it again and it ran fine. Does...
  22. 94f350

    Clutch pedal to the floor

    It's a crescent I think. Gonna fix it legit sometime today
  23. 94f350

    Clutch pedal to the floor

    So as it turns out the lever that pushes the master cylinder rod just broke, like a clean break. I used a vice grip to hold it together for the day until I fix it later.
  24. 94f350

    Clutch pedal to the floor

    I'm praying it's something easy and I won't have to pull the tranny
  25. 94f350

    Clutch pedal to the floor

    As I was about to leave to go to work this morning I went to step on the clutch pedal and it went straight to the floor, it was completely fine not even a minute before when I was driving it around my driveway. Can someone who knows how these clutches work explain it to me? I have a 1994 f350...

Latest posts

Forum statistics

Threads
91,297
Posts
1,129,899
Members
24,108
Latest member
Lance

Members online

Total: 488 (members: 9, guests: 479)

Share this page

Top