Search results

  1. S

    blinker fuse keeps blowing

    I do not know if your year truck is the same system as my 93, my recall on the brake part under the floor mounted to the frame fixed mine. Brake fluid was dripping onto the wire connector and popping fuse.
  2. S

    1993 E4OD flex plate/ crank shaft spacer

    My spacer looks very much like the picture from Frankenwrench.
  3. S

    1993 E4OD flex plate/ crank shaft spacer

    I am confused (not unusual these days). If I counted correctly, I have ten bolts to hold my flex plate onto the crankshaft. All the flexplates that I am seeing listed for a 93 NA IDI have nine. The flexplate I got from Rock Auto has nine. Did I get the incorrect flexplate or did I...
  4. S

    1993 E4OD flex plate/ crank shaft spacer

    My Flex plate has broke. It galled the mating surface of the thick spacer between the end of the crank and the torque converter. I am looking for a replacement part. Can file on mine but would prefer using a better one.
  5. S

    93 IDI with E4OD.

    Not happy with tranny yet. Drove today for the first time. Shifts poorly. I will check the outputs on the throttle position sensor, clean the connector contacts, do all the usual things to sort out poor shifting. It shifts like my old tranny did before replacing the solenoid pack. Kinda...
  6. S

    93 IDI with E4OD.

    Never mind. Counted pins and where pins go. Only one way it can go. Thanks
  7. S

    93 IDI with E4OD.

    I am trying to finish the install of my Monster Tranny. I have more gripes about the tranny, but will vent later. I did not pay close enough attention to which electrical connector goes to the MLPS and which one goes to the solenoid pack. It is not obvious to me. One connector is grey and...
  8. S

    cost of E4OD rebuild

    I sadly cannot recommend Monster transmissions. I am Very frustrated with the one I bought. Almost three months to get, then I had to use some of my parts out of my old tranny. The shifter shaft on the tranny I got was not for the style of MLPS that I had. If they knew i would have to pull...
  9. S

    E4OD from Monster Transmission for my 1993

    The linkage issue has been resolved. I should have read all the fine print. They expect you to replace their linkage with yours. It is surprising to me that I have to install my old shift linkage. I will post more on tranny after I install and drive it. Too soon to tell just yet. Their...
  10. S

    E4OD from Monster Transmission for my 1993

    Thanks for the reply. I have called and left message plus have emailed them. I will wait for there reply and update the results.
  11. S

    E4OD from Monster Transmission for my 1993

    Finally received my E4OD from Monster Transmissions after waiting nearly three months. I have the old tranny out and sitting beside the new one. I went to install the MLPS, but to my surprise, the length of the new shaft is about an inch shorter (the thickness of the MLPS) than the old one...
  12. S

    Where to find drive shaft parts?

    Thanks for all the replies. Found an OEM part on EBAY. Keeping fingers crossed.
  13. S

    Where to find drive shaft parts?

    93, NA, E4OD, Regular Cab, long bed, 2wd, one piece drive shaft. The front driveshaft yoke wore out. In need of a replacement. Anybody have an extra serviceable one laying around? Thanks in advance.
  14. S

    1993 manual pedals and steering column

    are the steering column and pedals still available?
  15. S

    E4OD troubles

    Thanks Rock. Sent him a message, waiting on reply.
  16. S

    E4OD troubles

    Having E4OD troubles in my 93 2wd, regular cab, long bed. Not able/willing to spend the necessary $ for the BTS solution. Looking for donor truck or parts collection to swap in a ZF5. Thanks in advance.
  17. S

    Will loose Torque converter bolts cause bad noises?

    Thanks to all that replied. Tightened nuts, noise went away. Yipppeee. I will do like suggested and use the blue locktight on the studs.
  18. S

    Will loose Torque converter bolts cause bad noises?

    Everything has been great with my '93 NA 2WD E4OD until the other night. Drove to work, no issues, cranked up to drive home, sounded like a can of nuts and bolts rattling around. I had to get home, so drove anyway. Noises stopped when underway, but came back each time I stopped at a light...
  19. S

    Seat Exchange

    Thanks for the replies. Looks like I will not be getting the CC bench. I'll start looking for Bronco seats.
  20. S

    Seat Exchange

    I have a 93 RC. My seat is in need of repair/replacing. I have found a rear bench from a 2000 CC Super Duty for less than getting new foam and seat cover from LLC. Will a rear bench from a 2000 CC SD fit into my 93 RC? I've used the search function and found up to '97 will bolt in, but...
  21. S

    Need slip yoke for 1993 reg cab E4OD 7.3 NA

    Thanks for finding your slip yoke. Turns out mine was not beyond repair. shop polished it and miced (and just how do you spell measuring with a micrometer, I don't think it's miked). I will not be needing yours after all.
  22. S

    Need slip yoke for 1993 reg cab E4OD 7.3 NA

    I think mine looks a bit different than the one in the pictures. Does it matter that the one in the picture does not have the big balancing ring on it? Or is the balancing ring a part of the drive shaft instead of the slip yoke. Truck is at the shop so cant go out to look. Should have it...
  23. S

    Need slip yoke for 1993 reg cab E4OD 7.3 NA

    Thanks, let me see how good/bad the one trans shop is gonna polish turns out. I will let you know if I still need it in a day or two.
  24. S

    Need slip yoke for 1993 reg cab E4OD 7.3 NA

    The tail shaft housing bushing wore out (caused by bad/old/original U-joint, near 200K). Taking truck to trans shop to repair. The housing is fine and shop was able to replace bushing. The slip yoke is slightly messed up. I need another one. Shop said they could not find another to replace...

Latest posts

Forum statistics

Threads
91,259
Posts
1,129,360
Members
24,084
Latest member
E Moeller
Top