Search results
-
What's it all worth?
Looking at doing a 7.3 PSD swap into my IDI.. and may have found a possible Donor truck that has a 7.3 powerstroke with 230xxx kms on it and zf5 manual. Just wondering what all my parts may be worth and if anyone would be interested in the various components if I did decide to go through with...- IDI Diesel7.3
- Thread
- Replies: 1
- Forum: 6.9L IH & 7.3L IDI Diesels
-
D60 swap? Or is there a way to adjust the lifted OBS toe in?
Hey guys, After putting the 4" Rough Country lift onto my f-250 with the TTB front end I noticed how bad the wheels are toed in. A wheel alignment fixed the side to side pigeon toe, but is there any adjustment to bring the top or bottom of the wheels in and out? Second question, what all...- IDI Diesel7.3
- Thread
- Replies: 13
- Forum: 6.9L IH & 7.3L IDI Diesels
-
e4od shifting issues after truck rebuild
The truck is a 1993/94 ford f-250 7.3 IDI turbo diesel. Gears are 4:10s and I went up to 315/75 tires (35s). The tranny was rebuilt and has around 5000k on it. I used a wiring harness from a 94' 2wd factory turbo that also had an e4od. Also the truck has a moose pump on it. So after finishing...- IDI Diesel7.3
- Thread
- Replies: 27
- Forum: 6.9L IH & 7.3L IDI Diesels
-
94' 7.3 IDI Build Update
Well haven't posted anything about the build in quite some time figured I'd make a new thread, the progress has been very slow, but its coming along. Since my last thread: -Installed Front and Rear Diffs (along with replacing every U-Joint, Bearing, and Seal I possibly could) -New Front...- IDI Diesel7.3
- Thread
- Replies: 16
- Forum: 6.9L IH & 7.3L IDI Diesels
-
New Batteries, New Cables, Blead Lines, No Start
Truck: 89' 7.3 IDI Diesel with Factory ATS turbo on it (motor is on bare frame, no wiring harness other than the one on engine) I dropped the motor into the frame and want to start it before i drop the body on to make sure everything is working fine, but as of now.. it is not First Try...- IDI Diesel7.3
- Thread
- Replies: 2
- Forum: 6.9L IH & 7.3L IDI Diesels
-
ARP Head Studs
Just ordered a set up ARP head studs for my 93' f-250 project. The motor is a 89' 7.3 IDI, they are listing a part number for the "kit" now, new for this year.. (wasnt able to find before as far as i've heard, I could be wrong). I'll get you guys that part # if you want tomorrow, came out to...- IDI Diesel7.3
- Thread
- Replies: 13
- Forum: 6.9L IH & 7.3L IDI Diesels
-
94' Factory Turbo 7.3 IDI Build
Heres the scoop -93' f-250 4x4 7.3 IDI N/A (using frame/drivetrain, and e4od transmission with less than 5,000k on it) -94' f-250 2wd 7.3 IDI Factory turbo (using turbo, body, and interior) -89' 7.3 IDI N/A (full rebuild, new crank, pistons, etc) So as far as the build goes -Sand...- IDI Diesel7.3
- Thread
- Replies: 23
- Forum: 6.9L IH & 7.3L IDI Diesels
