Search results

  1. RJMorrow

    Spindle bearing install

    Ok, I know I should've measured the depth of the bearings inside the spindle before I drove them out, but I forgot. Can anyone tell me how far to drive in the replacements? To be clear this is the inner bearing that the stub shaft rides on in the back of the spindle. This is for a Dana 50 if...
  2. RJMorrow

    Dana 50 Axle shaft needed-Drivers

    I am in the middle of a front axle rebuild and I have found my drivers side long shaft is not useable. This is the inner portion of the drivers side, from a '97 F-250. Thanks
  3. RJMorrow

    Front Diff leak

    So, I was in the middle of front wheel bearing replacement when I found that the previous owner had installed the inner spindle nut (dana 50 TTB) backwards. This meant the locking pin was smashed off and would require replacement. Because of this I had to order a replacement nut and the truck...
  4. RJMorrow

    WTB: Spare Tire Mount for a 1996 Ford F-250

    I am looking for parts to make up a spare tire mount. Either for sale local to western Pa or ship.
  5. RJMorrow

    New truck, new problems

    Ok, I am back, with a new '97 to add to my collection. Nicer condition than my '95 and runs much better. I have started taking care of the issues from the previous owner and I have found that the roof is leaking. It appears that maybe the roof gutters are split and leaking down into the ceiling...
  6. RJMorrow

    Power Steering Hose high Pressure Side

    I need an assist with my power steering hose. I blew the line last night and checking parts stores today gives me a hose which does not resemble what I took off. All listings for a non-hydroboost system give me this hose...
  7. RJMorrow

    Fuel leak at fuel line connection?

    I parked my truck in the garage the other day and when I went out the next day I had a nice diesel puddle under the front end. It appears the fuel line connections are leaking at the front frame rail? Is this a common failure? Is there an o-ring in the joint that I need to replace ? Will the...
  8. RJMorrow

    95 PSD Power Loss Questions

    I am back again for some more help. I have been experiencing power loss towing a trailer on hills. I will start up the hill, approx half throttle at 60mph and will loose more than 15 mph on the grade. At this point any further pressing of the accelerator will make no change. I suspect some type...
  9. RJMorrow

    Need help With Fuel leak

    Ok, I am back with a new problem and need some experienced help. I have a mild fuel leak from the bellhousing of my F-250. I did a quick search of related posts and inspected the top of my engine for the source of the leak. While the engine valley is filthy, I wouldnt say it was wet. Does anyone...
  10. RJMorrow

    7.3L Rusted oil pan options ??

    Ok, well I have a severely rusted oil pan and I am wondering what method to take in fixing it. The entire pan is not rusted, its just two REALLY bad spots. Just behind the starter the metal is falling off in chuncks and I expect paper thin. So, has anyone succesfully patched a pan like this...
  11. RJMorrow

    Another E4od problem ?

    Ok, I just completed a trans swap in my F250. Old unit had over 200k on it and was overheating and puking fluid, going into limp mode, etc. Now for the bad, the replacement unit, which I cannot swear to the history of, seems to have rather hard shifts. The unit is NOT in limp mode, I...
  12. RJMorrow

    another test

    test 2
  13. RJMorrow

    '95 F250 w/ E40d problems

    I am looking for a little expert advice here. My 95 F250 psd trans is starting to give me trouble. It is the E40D there is 300,000 miles on the truck, not sure about the trans. I find it will go into limp mode on random occasions. I undertstand bad sensors can be one source of this problem but I...
  14. RJMorrow

    Yet Another Hard Start

    I have a '95 F-250 7.3L which has become increasingly hard to start. This is a problem in any weather less than 60 degrees. I have checked my GP resistance and all are good, also verified GP relay operation. The truck does have a block heater which i replaced the cord end on and tried but did...
  15. RJMorrow

    95 7.3L PSD WATER SEPERATOR

    I am looking for a little help in locating the water seperator drain on my truck. If someone could supply a pic from this year range truck, I would really appreciate it. My truck did not come with a owners manual and the service manual just says to drain it, but not how to find it. I understand...
  16. RJMorrow

    95 PSD Rad Support w/AC

    I am in process of replacing front fenders and while I am into the front end, I am looking to replace radiator support as well. However, it appears that no one makes an aftermarket replacement for a '95 Diesel with AC ? I have read some other posts here and gather that I have the "tall" rad...
  17. RJMorrow

    Loose Shifter/Turn Signal Sw.

    I just bought a '95 F250 Auto 4x4 Ext. Cab. It appears to run well, although I might not know otherwise. But my problem is the column shifter is loose. I can move through some gears without pulling back towards me. Also it is very difficult to put into 1st. I disconnected the linkage at the...

Latest posts

Forum statistics

Threads
91,398
Posts
1,131,893
Members
24,216
Latest member
ajuka

Members online

Total: 403 (members: 9, guests: 394)

Share this page

Top