Search results

  1. Rawpower

    F350 Leaf spring material?

    Anyone know what steel is used in stock F350 leaf springs? Would it be 5160 alloy? :dunno Thank you, Rob
  2. Rawpower

    Broken DPS Headstud?

    Well, one of my driver's cylinger headstuds broke off. These were ordered from DPS about 2 years ago. Not many mile have been put on them at all, tops 6,000. I drove it for a few months, then the truck went into "build mode" and is now a project, so thats the reason for such low miles...
  3. Rawpower

    brake fittings?

    I was wondering if anyone knew what size brake fittings would be on the fittings where the caliper lines connected to at the frame were? I'll rephrase that to avoid any misunderstandings... The connection for the brake lines on both front (one on each side, bolted to the frame) and the rear...
  4. Rawpower

    Bus brakes, where to order?

    Hi, I don't think that this topic would fit in another forum as well as it does here, so I am posting it here. I am looking for brake rotors that have a 6 on 8.75" lug pattern and have the "rotor hat". I do know that a 1994 Ford B-700 meets these criteria, however... I cannot find a place to...
  5. Rawpower

    DMF weight

    Anyone know the weight of a complete assembled DMF for a 7.3L IDI Turbo?
  6. Rawpower

    10.25" spline

    How many spline are in a 93 350 10.25"? Should be 31, right? my memory... :rolleyes:
  7. Rawpower

    Rear seal on 2wd ZF?

    Obviously there is the traditional rear main seal on the ZF, but on a 2wd is there a seal that is supposed to go on the yoke behind the nut? I have a slight drip from there after overfilling the tranny. :rolleyes:
  8. Rawpower

    Finally, transmission reinstall

    I finally got my transmission reinstalled today. :draw My dad helped me out bc my brother is out of town, so many thanks to him. ;Sweet However, can I run Mercon V in my ZF S5-42? It seems to be a little thin. I would run 5-6 qts. of it, poured in via shifter hole. (I searched to see if...
  9. Rawpower

    Anerobic Gasket stuff... again :)

    So this stuff doesnt dry unless there is an absence of oxygen. Or in otherwords, it won't dry when oxygen is present. How will I ever get my tranny's new gasket to cure? :confused:
  10. Rawpower

    ZF reintallation

    Well its time for it to go back in... I pulled the ZF for two reasons. One, it was clearly in need of a rebuild, as it had begun popping out of gear occasionally and 2nd required double clutching or else it grinded badly. Two, I needed a 2wd ZF in order to run the divorced NP205. So I...
  11. Rawpower

    How to remove 3 shift rail retaining pins?

    Once again my knowledge is limited... haha seems like I find that out everyday. Anyways, does anyone know how to remove them AND reinstall them properly? EDIT: on an S5-42
  12. Rawpower

    Is the ZF S5-42's tailhousing gasketless?

    Before I install the tailhousing and stuff again, I just wanted to make sure that the ZF S5-42 is gasketless like the BW1356... If not, does anyone know how much the tailhousing gasket should cost? I'm guessing that the bearings rely on the gasket for clearance spacing & such, so RVT would...
  13. Rawpower

    syncros, forks, bearings, and seals?

    How mush sould all the synchros, all the shifter forks, all the bearings, and the internal seals cost on a 93 ZF-5 (should be an S5-42, not a 47 right?) Searched for the parts, couldn't find them anywhere... Thanks for your help in advance.

Latest posts

Forum statistics

Threads
91,372
Posts
1,131,193
Members
24,170
Latest member
Seven4eight

Members online

Total: 373 (members: 5, guests: 368)

Share this page

Top