Recent content by Leroy
-
Thought It Was Belt Drive, but YIKES!
Glad you found it! Sounded like something rubbing the fan to me, but knew it had to be something else, wiggling stuf is magic.- Leroy
- Post #9
- Forum: 6.9L IH & 7.3L IDI Diesels
-
'87 project- next round.
The large nut riding the governor rod is what adjusts the BASE IDLE / FUEL METERING SET POINT. Back out the external linkage base idle so that it is not making contact with the stop at run idle, then make your true base adjustment by the meter set point, but a hair, like 30-50 rpms low, now use...- Leroy
- Post #23
- Forum: 6.9L IH & 7.3L IDI Diesels
-
6.9 motor problem diagnosis
That's a really great idea, I never thought to ask.- Leroy
- Post #70
- Forum: 6.9L IH & 7.3L IDI Diesels
-
-
6.9 motor problem diagnosis
Awesome, I will definitely go for that tube then, yep gonna do more pullin off that truck in these next few days. I got to it with just a few hrs and I thought my alternator was not working so I left for home with a little less than an hour of daylight.. Little did I know, my McGiver...- Leroy
- Post #68
- Forum: 6.9L IH & 7.3L IDI Diesels
-
'87 project- next round.
After looking hard, but never finding a good answer about how to tune the DB pump, I just took one and by trial and error fugured out how to calibrate one while on the truck. This isn't the same as rebuilding a pump and calibrating it on a machine, the pump needs to at be good and run, but...- Leroy
- Post #8
- Forum: 6.9L IH & 7.3L IDI Diesels
-
'87 project- next round.
Maybe the pump is out of adjustment. 1) SET BASE TIMING 2) SET THE BASE IDLE / FUEL METERING SET POINT 3) SET DROOP CALIBRATION 4) RETIME PUMP 5) DRIVE FAST- Leroy
- Post #7
- Forum: 6.9L IH & 7.3L IDI Diesels
-
6.9 motor problem diagnosis
Yeah, the stock lines are nylon on my 85, it's you know it's the same concept, plastic, I did order all new rolls of the stock size 3/8 and 1/4 and, routed my fsv out of the equation for now until I put manual valves in. I have heard that the big rig lines are nylon and work well for fuel...- Leroy
- Post #65
- Forum: 6.9L IH & 7.3L IDI Diesels
-
6.9 motor problem diagnosis
Yeah it's been raining a lot, I did look under there and there's a good mitsu starter, and a fresh looking trans.. I weren't sure if the little tube was a press fit also, I figure likely it is? I woulda had to crawl like a mud bug and remove that starter to try and grab at it and pull it out...- Leroy
- Post #64
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Forde E350 short school bus 7.3L IDI - surging at idle
It sounds like a failing fuel pump, fuel restriction, sucking air, or a failing injection pump. In order of hopefulness of what the problem is. I would recommend replacing the lift pump first, add a fuel pressure gauge and check for pressure, and flow out of the fuel filter base schrader...- Leroy
- Post #9
- Forum: 6.9L IH & 7.3L IDI Diesels
-
New project '87 6.9 f250
Looks like a gem. I would plug in the block heater, while it's warming up a few hours, throw a hot battery in it, disconnect the glow plug contact relay, check the oil, loosten the injector lines to purge any air, roll it a few feet out the garage, crank with the throttle to you see puddles...- Leroy
- Post #9
- Forum: 6.9L IH & 7.3L IDI Diesels
-
6.9 motor problem diagnosis
Looks like outside diameter of 1/2in PEX is 5/8 .. 0.625 this 5/8 inside diameter A1 fuel line at .625 will slip right over it with a little flare, some grease and some clamps...- Leroy
- Post #60
- Forum: 6.9L IH & 7.3L IDI Diesels
-
6.9 motor problem diagnosis
Hey, these are some great ideas, I bet they could be flared, I never have tried a heat gun, but that would be great to avoid fittings and routing up to the engine bay. Those quick disconnect o ring fittings in a few places would sure be nice too. A quick search found that PEX is the same...- Leroy
- Post #58
- Forum: 6.9L IH & 7.3L IDI Diesels
-
6.9 motor problem diagnosis
From what I gather, PEX is 'half' as resistant to diesel as water. and not good for under pressure above 200 degrees. There are some, but not many arguments for and against using it as fuel line on the internet. I can find some examples of .. "yea, but i've been using it for years, and it...- Leroy
- Post #56
- Forum: 6.9L IH & 7.3L IDI Diesels
-
6.9 motor problem diagnosis
I'm gonna run entirely with PEX and upgrade the fuel pump, I'll adapt fittings where need be. I think i'll install 2 seperate, cheaper, electric fuel pumps with a filter behind, and check valves ahead of each. In case of failure can toggle the secondary pump. I used to like mechanical fuel...- Leroy
- Post #55
- Forum: 6.9L IH & 7.3L IDI Diesels
