Recent content by FarmerFrank

  1. FarmerFrank

    WTB: gears or whole rear axle.

    Dont know why I thought of this earlier but lucky I checked back. I bet I still have the gears but I know I dont have any yokes. My bronco blew one out this summer and I discovered I didnt have any left. Sent from my SM-G970U using Tapatalk
  2. FarmerFrank

    crank sleeve install

    Use the torque ring for the flywheel bolts and some 5/8 nuts or a big stack if washers on the bolts. Go slow and even and let it slide on gently. I like to add a thin coat of red or blue loctite to the crank to ensure a good seal because your going to cut it off anyway. If your talking about...
  3. FarmerFrank

    SAE #3 adapter, flywheel/flexplate questions

    That is kinda how a c6 flex plate is. A heavy “flywheel” with holes and a thin flex plate that bolts directly against it. You reach through the holes to unbolt the converter Sent from my iPhone using Tapatalk
  4. FarmerFrank

    What am I even doing sometimes

    I have been wanting to do the blue LED’a in my truck but damn, I think I’m going to try the red instead!! How many are back there? Been a while since I’ve had mine out Sent from my iPhone using Tapatalk
  5. FarmerFrank

    WANTED!!! 385 series 460 d0ve-c heads

    Now I could be wrong, and I have been wrong before but aren’t C8, C9 and D0 heads the same? CC are the same size and valves only changed for the thunder jet, cobra jet and allegedly the police interceptors Sent from my iPhone using Tapatalk
  6. FarmerFrank

    waste veggie oil

    Willing to sell only a drum or so? Sent from my iPhone using Tapatalk
  7. FarmerFrank

    Oil pan removal

    Then you will have to pull the engine out of the truck. It’s not that big of a job after you’ve done a few. I’d suggest trying to seal it in the truck first. If it falls then pull the engine or cut a hole in the pan to get it out.
  8. FarmerFrank

    parts needed

    I’d accept 1 million for it but I am open to offers. Sent from my iPhone using Tapatalk
  9. FarmerFrank

    Remove, weld, reinstall power steering pump bracket?

    That’s good it worked out but I still would have expressed my opinion on how he should have called first. Heck I’ll call a customer if I find an option that would save them money vs the route we agreed on when they dropped it off. Sent from my iPhone using Tapatalk
  10. FarmerFrank

    7.3 isi injection pump tester

    If you have a spare set of lines to hook on your questionable pumps, just keep swapping them out and see how they run. My best IP swap time ( new pump with all lines and fittings ready to go) was 18 minutes from start to engine start. If you have a turbo add 10 minutes. Sent from my iPhone...
  11. FarmerFrank

    Wanted: Factory turbo airbox for IDI

    I have the top of the air box, if you only find a bottom let me know Sent from my iPhone using Tapatalk
  12. FarmerFrank

    parts needed

    I got a spare shifter Sent from my iPhone using Tapatalk
  13. FarmerFrank

    Unbelievable luck

    Hmmmm.... you buy the parts, I’ll Put in the clutch kit and I get Hank for labor? Sent from my iPhone using Tapatalk
  14. FarmerFrank

    LUK 07-225

    Your fine. Diesels are all the same bell until 6.0's. I have an s-42 from an idi on my powerstroke. Sent from my iPhone using Tapatalk
  15. FarmerFrank

    unusual clutch issue

    Glad you found it. I had a similar issue in a 90 bronco when I was 17. Got so bad you could hardly pull out. Found 2 bellhousing bolts left and they were finger tight, every time I pushed in the clutch I was moving the transmission back 3/4"... Last guy must have used his biggest screw driver to...

Forum statistics

Threads
91,217
Posts
1,128,474
Members
24,044
Latest member
Mnlx

Members online

Top