Recent content by Boltgun
-
Would you change these??
The guided seals will come out in two pieces if you use the pry bar method ( like I do), just stick your 24" pry bar back in there and nudge the guides out.- Boltgun
- Post #8
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Would you change these??
Your already that far into it, might as well.- Boltgun
- Post #2
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Clutch Rattle...
That was my first thought, but usually throw out bearing noises change when pressure is applied or taken off, this is more consistent. It's also a pronounced rattle, not your typical bearing noise. I'm at a loss here.- Boltgun
- Post #7
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Clutch Rattle...
Not the insp cover, no heat shields that I can find.- Boltgun
- Post #5
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Clutch Rattle...
Negative, replaced with a SMF luk kit about 6 months ago.- Boltgun
- Post #3
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Clutch Rattle...
..that doesn't seem to be clutch related? Short version, loaned my truck out and when I hopped in it to go to work two days later I hear a metallic rattle from underneath the floorboard. Nothing that sounds catastrophic or anything, but extremely annoying. Got to work and crawled...- Boltgun
- Thread
- Replies: 7
- Forum: 6.9L IH & 7.3L IDI Diesels
-
PSA: Change your caliper pins
All good advice fellas, I like the permatex ultra caliper grease myself, nice and tacky.- Boltgun
- Post #5
- Forum: 6.9L IH & 7.3L IDI Diesels
-
PSA: Change your caliper pins
Those two pieces of metel bonded together with a little bit of rubber that hold your caliper on, yea replace those. I "inspected" them the last time I did a brake job, and had one disappear on the ride home yesterday. Fortunately I was less than a mile from the house so I limped it home...- Boltgun
- Thread
- Replies: 8
- Forum: 6.9L IH & 7.3L IDI Diesels
-
-
-
Parting Out: 87 F-350
Parting out an 87 F-350. Standard cab long bed, blown 6.9, ZF-5, 4x4. D60 and all related components are gone, bed is already spoken for. Blue interior, blue/black two tone body is pretty straight ( minus the front bumper and grill). Now here's the rub, truck is at a buddy's place...- Boltgun
- Thread
- Replies: 11
- Forum: Marketplace
-
Wanted: Front drive shaft slip yoke for 1985 Ford F350 4wd
Double cardan should be on the transfer case, slip yoke towards axle. Not sure about the yoke itself, but you can buy the whole shaft from napa. Not cheap.- Boltgun
- Post #3
- Forum: Marketplace
-
-
what shares tach and voltage gauge wires?
Yea, the intermittent working makes me believe it's a bad ground and/or bad connections on the cluster itself. One day it will bother me enough to pull it apart and start looking.- Boltgun
- Post #14
- Forum: 6.9L IH & 7.3L IDI Diesels
-
what shares tach and voltage gauge wires?
If I've been running around with no tach for the last 7 years because of a blown fuse I'm gonna be ticked...- Boltgun
- Post #12
- Forum: 6.9L IH & 7.3L IDI Diesels
Latest posts
-
Supply fuel line from fuel filter housing to injection pump- Latest: SkylabTech86IDI
-
-
-
