ZWilson07
Cowboy
Just a reminder guys to check your fuel filter from time to time, the water separator, etc. I just went through the worst time ever draining it, getting my bottom separator off, and getting my actual fuel filter off. I ended up having to stab the filter with a screw driver to finally get it off.
Also found out some good and bad news. Bad news is my fuel filter was the factory original! No not the same kind, THE factory original with factory engine overspray on it that is 25 years old
. Granted I don't have many miles on my truck but still; good news is this truck amazes me all the time how all its factory parts still last this long and I am just now starting to have factory parts break from old age after 25 years.
Now obviously I am definitely not recommending to run it that long and yes I should have already changed it, but hell even if I would have done it when I got it, it still was 23 years old at the point.
I have noticed we have a lot of new people popping up as well so I figured I would throw this in here and the reason I worded the title of the thread as I did so that it would be easily found for people searching. I know most of us know this but just for any new people that want to know.
1. Water Separator Drain is standard thread.
2. Water Separator Drain Bowl is standard thread.
3. Fuel Filter is standard thread.
Now
(1) The drain can be a little confusing. It is standard thread but when you turn it to the left to loosen it and drain liquid, it actually goes up into the separator itself. It does this so that the rubber stopper inside of the separator rises and releases liquid out. So it is the normal lefty loosey, righty tighty but looking at it at first might confuse you. Turning it to the right makes the drain go down away from the separator even though it is tightening it, but this is because it is pulling the rubber stopper down to seal.
(2) The drain bown itself again is standard thread but since it is facing down it can get you for a second.
(3) Fuel filter itself is also standard thread but since it is facing down it can get you for a second.
For (2) and (3)
-This means if you are standing next to the passenger fender/tire and facing the motor you will have the battery on your right side, and the firewall/passenger seat on your left side. You will take whatever device you are using to remove it and will start from the battery to your right and your hand will rotate left across your body towards the firewall/passenger seat.
All this is very simple and most of us know but when stuff is stuck on there, not wanting to budge, your frusturated and trying to get it done, sometimes we can get mixed up. Even my factory 1990 manual does not specify if the threads are clockwise or counter-clock wise, it just simply states unscrew/loosen and screw/tighten.
Hope this helps somebody one day.
Thanks
Also found out some good and bad news. Bad news is my fuel filter was the factory original! No not the same kind, THE factory original with factory engine overspray on it that is 25 years old
Now obviously I am definitely not recommending to run it that long and yes I should have already changed it, but hell even if I would have done it when I got it, it still was 23 years old at the point.
I have noticed we have a lot of new people popping up as well so I figured I would throw this in here and the reason I worded the title of the thread as I did so that it would be easily found for people searching. I know most of us know this but just for any new people that want to know.
1. Water Separator Drain is standard thread.
2. Water Separator Drain Bowl is standard thread.
3. Fuel Filter is standard thread.
Now
(1) The drain can be a little confusing. It is standard thread but when you turn it to the left to loosen it and drain liquid, it actually goes up into the separator itself. It does this so that the rubber stopper inside of the separator rises and releases liquid out. So it is the normal lefty loosey, righty tighty but looking at it at first might confuse you. Turning it to the right makes the drain go down away from the separator even though it is tightening it, but this is because it is pulling the rubber stopper down to seal.
(2) The drain bown itself again is standard thread but since it is facing down it can get you for a second.
(3) Fuel filter itself is also standard thread but since it is facing down it can get you for a second.
For (2) and (3)
-This means if you are standing next to the passenger fender/tire and facing the motor you will have the battery on your right side, and the firewall/passenger seat on your left side. You will take whatever device you are using to remove it and will start from the battery to your right and your hand will rotate left across your body towards the firewall/passenger seat.
All this is very simple and most of us know but when stuff is stuck on there, not wanting to budge, your frusturated and trying to get it done, sometimes we can get mixed up. Even my factory 1990 manual does not specify if the threads are clockwise or counter-clock wise, it just simply states unscrew/loosen and screw/tighten.
Hope this helps somebody one day.
Thanks
Last edited: