I decided to purchase the DTI Timing light , because I am not having much luck with the probe. Do I need to bring the engine up to 2000 rpm with the timing light to get a proper adjustment ? any other tips on using the light ? Thanks.
Well I tried agian , when I rev it up i was getting lower numbers , but negative. when I shut down the truck , the unit read -7. So i thought i would try moving the pump a dime width toward driver. Same results all kinds of negative numbers when i shut it down it displayed -15.3. Also when...
No. 1 passenger side by the Radaitor with the pulse adaptor. Instructions also say " if the magnetic probe is not close enough to flywheel or is not connected properly, timing unit will display the correct RPM but the degrees shown will be the negative value of the offset programmed into the...
I did turn it to off set and it was already at 20 high setting ,then too probe , started Truck got 650 rpm and - 20 degrees. After reading instruction I may of had the probe hooked up before the battery connections , which in the fine print it tells you not to do. Hope that did not damage it. I...
The engine starts great and runs good , but unfortunatlyI have a small fuel leak coming off the back of the R&D pump. I can't see where its leaking from, I was thinking ill cover it with powered chalk then look for the sourse of the leak, hope its not the pump. If its the injection lines i...
Yes , I did not have the problems some have had getting it in. i used a card pushed it all the way in them pulled out the card. I checked that it was going in far enough. I might try moving Pieso clamp right above injector , and make sure its running 2000 rpm.
i tryed to time my new pump today, with this unit. Off set at 20 . RPM is 650 but timing shows - 20 ? Do I need to rev it up to 2000 rpm to get a correct reading ? Piezo clamped on straight section of # 1 inject red lead with black/ground clamped to same line. I did rev it some but all i get is...
I,am in the process of restoring my truck. I have the box off , i have pianted the frame and have the aft fuel tank back in . I want to leave the forward tank out to do brake line and body mounts. My front window is leaking and I want to know if the Truck will run with just the aft tank .so i...
I have used a few ,but mostly Stanadyne & PS Diesel Kleen. lately the PS Diesel Kleen , every tank full gets a dose. Also I have never turned up the fuel or done anything with the pump. Dont run my tanks below 1/4 tank , for the most part. Also still running a Machanical lift pump.
I am still running the 1994 factory sealed turbo Stanadyne DB2 Injection Pump , 400000 + KM . I know its way over due for a rebuild , recently my Truck does not go to high idle at least not right away as it use to . I thought it would be the sensor / switch by the thermostat, just have not got...
My truck has not been going to high idie , at least not right away. I bought a new high pressure temp switch , i see it threads in just behind thermostat , my question is do I need to drain off some coolant or is this switch on the oil side of the block ? thanks for your help.
Yes, its clean and it all works with lights. Thanks to Cluster Fix. As for KM to Miles you guys must be using the dollar conversion, that would be 248548.477 miles.just getting broken in.
I have to agree, never give up on these Trucks. I have been keeping mine going since new , there were times when I almost gave up on her, 400000 KM later I cant believe what a reliable Truck it has been. No major Engine or Transmission work done,still running strong.
I had my wiring harness for Cruise Control replaced, there is a recall on our trucks,risk of fire. Harness plugs in beside brake reservoir.I have 1994 IDI Turbo Diesel.
No hot start issues here, had that problem a couple years ago,replaced the starter and it was golden.I do use fuel additive ever fill up,no major engine work to date,nothing done to transmission. pretty sure its going to out last me.
Almost embarrassed , mine has original fuel pump & injectors 394000 KM / 244820 miles. Starts first time, I get a little smoke on start up. Runs great ,I'am sure its down on power from new, been planning to renew them for a while.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.