Search results

  1. Kizer

    Still smoke issue

    "when I’m accelerating at a steady pace, at around 1700 rpm’s it’ll occasionally spike 2-300 rpm’s for like 2 seconds, then drop back down"
  2. Kizer

    Still smoke issue

    Got it. All of my IDIs are bolt action...I didn't even think about FIPL being out of spec. I haven't looked, but there's probably something the "Tech Article" regarding FIPL adjustment/troubleshooting.
  3. Kizer

    Still smoke issue

    That was helpful! The whole forum appreciates it, I'm sure. Perhaps "facetime" would be a better fit for you.
  4. Kizer

    Still smoke issue

    Spike in RPM is usually associated with air intrusion. At one point, I had "the perfect" air intrusion on the '93. Hard acceleration was causing air to enter the fuel system at the FSV. Result: It felt a little like hittin' the NOS button on a gasser. It was kinda' cool, until the air...
  5. Kizer

    Help with unconnected wire under the hood, ‘94 F350 7.3 IDI turbo diesel.

    If I've got the correct wire, it goes to the sensor on the drier.
  6. Kizer

    Help with unconnected wire under the hood, ‘94 F350 7.3 IDI turbo diesel.

    I don't remember where that goes. I'll be home tomorrow... I'll take a look and let you know, if you don't get an answer before then If you're in a hurry, AutoZone site has wiring diagrams.
  7. Kizer

    rotary fuel pump

    I'd like to help you understand. Replacement mechanical pumps are (generally) c**p, these days.
  8. Kizer

    5.5 mm (.217 Inch) Bore Scope (to inspect timing gear alignment)?

    Hello Ladies, Gentlemen and F ***n' Robot, It's been a minute since I've had the IP (timing) gear cover off of one of our trucks. Do any of you, robot excluded, know if a bore scope (5.5 mm max diameter) will get me past the IP gear and the cover? I remember that the "putty knife/plumber's...
  9. Kizer

    Cup holders

    Perhaps post #556, in this thread, will give you some ideas!
  10. Kizer

    Throw out bearing noise?

    Not to be argumentative, but I've had a different experience with several "cheap" TOBs over the last few years. They "chirp" with the pedal out at idle and when driving...stop "chirping" with the pedal depressed. Regarding the "pulse" that's felt through the shift lever ... that's a new one...
  11. Kizer

    Effect of timing adjustment?

    Good luck brother. See "Hall of Shame"
  12. Kizer

    Door Hinge Hardware Question

    Jeez, I really and truly hate the violation of my 1A rights that this robot is committing. If I knew how, I'd give it a "taste" of my 2A.
  13. Kizer

    Door Hinge Hardware Question

    ****** = j u n k i e Thanks again, stupid *******'n robot.
  14. Kizer

    Door Hinge Hardware Question

    One of my favorite websites. I'm like a "****** in a drug store" when I go there.
  15. Kizer

    Door Hinge Hardware Question

    Based on the number of views Vs. replies to your question, I believe that I'd invest in a set of "thread checkers", if I were you. For me, it's been "one of those tools" that I hated to spend money on, but has been useful on NUMEROUS occasions.
  16. Kizer

    Serpentine Belt Squealing

    It does sound like you should drain/flush and refill you PS oil. Maybe consider an inline filter as well. Additionally, I've had zero luck running the belt that the part robots call for. I've been using a shorter belt. It works great but it's definitely more challenging to install.
  17. Kizer

    Milwaukee Battery to Run IP / Wiring ?

    The link that I posted, for the "stepdown" is advertised as working with the kids' cars. With the information that you shared, I believe that I can make that work pretty nicely . Thank you again.
  18. Kizer

    Milwaukee Battery to Run IP / Wiring ?

    Damn Brother! Thank you very much for the insight and information! It's much appreciated. I promise to let you know how this works out .
  19. Kizer

    Milwaukee Battery to Run IP / Wiring ?

    Man, I wasn't really even thinking of getting home . I just wanted to get (all of us) off of the side of that 2 lane road. Turns out that 17 miles would have gotten us to an abandoned fuel station...not great, but better.
  20. Kizer

    Milwaukee Battery to Run IP / Wiring ?

    Pretty funny. I've wanted to try this idea since I was stranded in BFE Oklahoma. I drove an '03 F150 to Ft. Smith, Arkansas, with my equipment hauler and dog in tow, to purchase an IDI. I bought the IDI, swapped the trailer over and loaded the F150 on the trailer. The IDI slung the...
  21. Kizer

    Overhead Gauge Cluster

    It's looking good sir! Just in case that you're interested in my $2 (5 years ago it would have been my 2 cents), I believe that I'd consider lowering the profile as much as possible. Additionally, if you haven't checked the McMaster-Carr website, they have hinges that may inspire you.
  22. Kizer

    WANT TO TRY A LIL BUDDY HEATER TO WARM ENGINE

    Would you consider selling your cruise control cable to me, before you give this idea a run? I promise to give it a good home and you're probably not going to need it,
  23. Kizer

    Milwaukee Battery to Run IP / Wiring ?

    I'd planned for the Milwaukee battery to be in the cab. I like the "switch" idea. Thank you.
  24. Kizer

    Electrical issue

    Alright sir, I'll agree that "it ain't hard". It is, however, an a** whippin' for me. I ran around the truck, for the better part of two hours, testing and re-testing ... still had a draw. It turned out to be the fusible link to the GP controller.
  25. Kizer

    7.3 temperature gauge dropping under load

    x2 Or search "fan clutch mod", or some such. I've got a post on it, from way back.

Latest posts

Forum statistics

Threads
93,000
Posts
1,155,989
Members
26,589
Latest member
tke395

Members online

Total: 587 (members: 6, guests: 581)

Share this page

Top