Search results

  1. BioFarmer93

    Windshield banner

    http://www.windshieldbanner.com/
  2. BioFarmer93

    NEW STARTER - OMG!

    Well, I'll be honest with you- I have significant neuropathy in my fingers and no longer can "see" with my fingertips like I used to. It took me a solid ten minutes to get the socket on the head of that bolt the first time when removing it. When it was time to reinstall it I did like Icanfixall...
  3. BioFarmer93

    NEW STARTER - OMG!

    Yes in deed! -and speaking of roll starting, this morning was the last key start on the old starter... This afternoon after work was a no-go. Good thing I got there a little early and got a good spot in the garage -right at the top of a ramp. I cycled the plugs, put it in reverse and rolled...
  4. BioFarmer93

    NEW STARTER - OMG!

    I've read about it here, but just couldn't imagine what it must be like... Now I know. Just put a new Mitsubishi gear reduction starter on this evening and I can not believe how incredibly fast Henry starts! Between the Baby Moose and a fresh starter, you cycle the plugs, bump the key and he's...
  5. BioFarmer93

    Poor Mileage?

    -MAYBE THE SAME REASON MY MPG WENT DOWN AFTER THE BABY MOOSE INSTALL... I CAN'T KEEP MY FOOT OUT OF IT!!LOL:dunno
  6. BioFarmer93

    SOMTHINGS WRONG!!!!

    Benton, The amp meter needle bouncing up and down sounds like classic voltage regulator end-of-life spasms.. Also the cheapest and easiest thing to start with. You really ought to get yourself an inexpensive multi meter though, they come in real handy for all kinds of stuff.
  7. BioFarmer93

    Show off your WMO/WVO filtration setups

    Here's mine.. There is one more there also. http://www.youtube.com/watch?v=GjznCg_ST6I
  8. BioFarmer93

    Replacing the Fuel Cutoff Solenoid?

    Pele, Charge the batt's back up, re-loosen those 6 lines, disable the glow plugs temporarily and have someone hold the pedal continuosly on the floor & crank while you watch the the lines... She'll eventually get fuel to the injectors, she's just pissed that you let her sit so long with no...
  9. BioFarmer93

    intercooler setup/fabrication

    3M makes a spray adhesive called Super 77. Spray both pieces, wait 90 seconds, push the boot on and tighten the clamp. I sure hope you don't ever have to take it apart...;Really
  10. BioFarmer93

    soup bowl mod

    Here, it's not to scale, but you get the idea...
  11. BioFarmer93

    how many flats can u turn the ip screw up from stock to full fuel

    OK, also in the realm of "no dumb questions" I need to turn my pump down a little, because I'm wasting fuel in clouds of black smoke.. So which direction is up/down- in or out/ clockwise-counter clockwise??:dunno
  12. BioFarmer93

    Winches

    -this looks to be pretty good & will fit your budget...
  13. BioFarmer93

    Electric fuel pump power wire

    -straight from the battery->fuse->switch->pump. It makes enough noise that I don't forget to turn it off LOL
  14. BioFarmer93

    anyone ever use one of these pyrometers?

    LOL You guys are overlooking the obvious- David IS young. Young eyes much more easily refocus than our old eyes... I'v noticed the same thing, a lag time in focusing between far & near, especially later in the day after a full day's worth of eye strain.
  15. BioFarmer93

    WMO Filter Setup

    Who is getting all of this unwanted attention about untaxed fuel? Do you mean just regular folks driving around in pickup trucks? If you are not selling it, how can the govmt demand more taxes on petroleum that has already been taxed and discarded? Anyway- to get back on topic, as was...
  16. BioFarmer93

    is this fuel pump any good?

    Trapper, Don't sweat it man- that pump is gauranteed for 6000 hrs. and is OEM on lots of stuff-, including service as a diesel lift pump. It looks funny but that's where the humor stops, it's a top rated pump & I'm lovin' my Facet, it blows the Holley Red away & can supply cold WMO to the baby...
  17. BioFarmer93

    Engine cleaning

    Hey brother- what happened to that whole "bitter clingin' " thing??:D
  18. BioFarmer93

    biodiesel

    John, Javier has a point.. If you are talking about REAL biodiesel (B100) that is well made and chemically correct, you can run up to about 20% mixed in with ULSD* with minimal worry about seals breaking down. Be aware though, that biodiesel will thoroughly clean out built up crud and sludge in...
  19. BioFarmer93

    Holly Red, description says not for fuel injection?

    http://www.jcwhitney.com/gold-flo-solid-state-fuel-pumps/p2005664.jcwx?skuId=280013&filterid=j1
  20. BioFarmer93

    Holly Red, description says not for fuel injection?

    The fuel injection they're talking about is the medium/low pressure injection used on gas EFI engines- it has nothing to do with the Holley's use as a diesel lift pump for our application. However I will say, that even though a lot of folks use them (me too) as lift pumps for our trucks, they...
  21. BioFarmer93

    Reman IP Pumps (besides moose)

    Baby Moose- $513.92... But I had an exceptionaly good core, come to find out. Absolutely amazing-;Sweet;Sweet
  22. BioFarmer93

    need fuel lines

    $40+postage...:D
  23. BioFarmer93

    IP Wrench- cheap & almost easy

    $17 for a wrench that I still have to work on:eek: OldBull sir, you MUST be independently wealthy. I like this idea better, go to the local pawn shop and in that bin they have in the middle of the tool section, grab a handfull of mix-n-match 9/16 box ends, do the mod on them, and send them to...
  24. BioFarmer93

    IP Wrench- cheap & almost easy

    No, it wouldn't be too much to ask.... Now all I have to do is remember!LOL:D Seriously though, if I can remember to do it I will, since its only a matter of switching tanks and a 5 minute high idle to purge the line;Sweet
  25. BioFarmer93

    IP Wrench- cheap & almost easy

    Great minds...... Why near the open end? My thinking was that the box end is a twelve point, so that would give me twice as many positional options for working in a confined space. But no matter, did it work OK for you is the question?

Latest posts

Forum statistics

Threads
93,000
Posts
1,155,990
Members
26,589
Latest member
tke395

Members online

Total: 657 (members: 5, guests: 652)

Share this page

Top