Recent content by towtruckdave

  1. towtruckdave

    Tried everything on this bronco and Facebook isn’t nearly as helpful as this forum!

    How long have the headers been on? Did you put a new o2 sensor in? Also check if you have 12+ vdc at iac, if you do, then try a known good (different) iac that is for a truck the same year. Junkyard is a good source. Did you check eec voltage?
  2. towtruckdave

    The Official "Show Us Your Ride" pictures of member's trucks thread.

    Hi Fellas, this is one of the rigs that I have had for a while now. Too bad it is not an idi, but I am posting it anyway because I think it is a cool truck. This is a true Nite Bronco. 1992 5.8l e4od 3.55 limited slip. Old but everything works ;)
  3. towtruckdave

    1991 7.3 IDI engine, runs $500 SOLD

    This 7.3 IDI ran strong but did use a quart of oil every week. I stopped driving the truck a year ago after the door and cab got smashed in an accident. I have had it in there since it was freshened up in 2011 with rings, bearings and valve job. It has not been overheated or run low on oil. I...
  4. towtruckdave

    ZF5 diesel 5 speed 4wd transmission. SOLD

    I would be willing to ship. If you pay shipping, I will leave the transfer case on it :Thumbs Up
  5. towtruckdave

    ZF5 diesel 5 speed 4wd transmission. SOLD

    I am in Wayne County TN. I do have 2 good 1356 cases.
  6. towtruckdave

    Rear axle speed sensor questions

    I was pretty sure that this rear axle out of my 1990 F250 idi would not work in my 1992 e4od bronco because the 1990 axle has no speed sensor for the trans computer to read. Now I am reading that my e4od has a electric speed sensor in the tailshaft and the diff tone ring is for abs ( I don't...
  7. towtruckdave

    ZF5 diesel 5 speed 4wd transmission. SOLD

    For sale is a good zf 5 for a diesel. It has a good clutch and flywheel. It fits 4 wheel drive F250 F350 and F450 2wd and 4wd. Complete! $550 cash Dave 931-206-7398 text or call I am looking for nice 1992-1996 F series/Bronco front bumper, fenders, doors, rear axle 3.55 ratio
  8. towtruckdave

    Dana 60 F350 front axle SOLD

    For sale is a good working low miles D60 w/3.55 gear. Kingpin style. It comes with everything you need to install in place of a ttb in an F250. Shaft, good F350 leave springs, brackets, hangers, bolts, pitman, steering box, tie rods, cross bar good calipers, rotors, pads and even a steering...
  9. towtruckdave

    What to do before new IP?

    Actually you should be able to feel a little play back and forth. It is hard to explain in words, just be very careful.
  10. towtruckdave

    Who has put an idi in a 92-96 bronco?

    Thanks for the replies! I have a rust free Dana 60kp, idi-zf5, hydroboost 1990 sclb in my driveway. It has a sideswiped cab and cracked up core support and fenders. Yall got me thinking about shortening it and topping it with a 92-96 bronco body.
  11. towtruckdave

    What to do before new IP?

    You may want to familiarize yourself with the pitfalls you can fall into when installing your fresh injection pump. If you even start to tighten the housing bolts without the IP drive gear in perfect mesh, you can damage your IP and gears. Watch you do not get sealer on the gears.
  12. towtruckdave

    Who should I trust to rebuild this injection pump?

    Thanks fellas, the injection pump is on its way to Mel. ;Sweet
  13. towtruckdave

    Who has put an idi in a 92-96 bronco?

    I am wondering if the frame and suspension are able to handle the diesel and if it handles ok? Thx:yell:
  14. towtruckdave

    Who should I trust to rebuild this injection pump?

    Hi everyone!!! Sorry I have not been around for a while. I have a non idi IP that needs fixed. I know this is the idi forum but I trust y'alls opinion so here I am. The IP is what I believe to be a bosch ve10. It is off a 2002 Massey Ferguson 5435 with a Perkin's 1104. It was surging...
  15. towtruckdave

    Hey fellas! Just wanted to say hi.

    Thanks guys! I hope your holidays are going good ;Sweet
See more

Latest posts

Forum statistics

Threads
91,284
Posts
1,129,785
Members
24,099
Latest member
IDIBronco86

Members online

Total: 644 (members: 2, guests: 642)

Share this page

Top