Recent content by stony7933
-
E fuel pump hose splicing
By chance you know which part number would be the best match? The ones that say 4-7 psi is only good to 150hp- stony7933
- Post #16
- Forum: 6.9L IH & 7.3L IDI Diesels
-
-
E fuel pump hose splicing
I'm just trying to get this truck running the best it can cause I'm using it as a tow pig for my trailer and drag car. I've put an injection pump on it, new return lines and those plastic pieces, water pump, thermostat, got glow plugs, redoing all the brakes with pads and calipers and lines up...- stony7933
- Post #13
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Zd29s vs Zd9s...for the inquiring mind...
I just got my zd29s in the mail today from rock auto. They came in the motorcraft bags. So I guess we will see how it goes.- stony7933
- Post #69
- Forum: 6.9L IH & 7.3L IDI Diesels
-
E fuel pump hose splicing
Thanks for the input guys... It's much appreciated.- stony7933
- Post #11
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Zd29s vs Zd9s...for the inquiring mind...
Ok I will do that with my signature. I've been looking at some of the other post about it but was kinda confused by some of them being new to diesels- stony7933
- Post #63
- Forum: 6.9L IH & 7.3L IDI Diesels
-
E fuel pump hose splicing
Or is there another pump you would advise using- stony7933
- Post #6
- Forum: 6.9L IH & 7.3L IDI Diesels
-
E fuel pump hose splicing
So would I have to T into the existing return line then or how would I do that... Any advice on this stuff is very appreciated...- stony7933
- Post #5
- Forum: 6.9L IH & 7.3L IDI Diesels
-
E fuel pump hose splicing
I figured with running a higher pressure pump they might leak or blow off... Was thinking of using a Holley red pump. I really like the idea of the faucet pumps but I'm noticing everyone seems to be moving away from them because of the higher demand drop in pressure and starvation- stony7933
- Post #3
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Zd29s vs Zd9s...for the inquiring mind...
Do you have a picture or schematic on how to make a manual push button setup... New to the diesel world but I like this idea- stony7933
- Post #60
- Forum: 6.9L IH & 7.3L IDI Diesels
-
E fuel pump hose splicing
Does anyone have pictures of how they have there e fuel pumps sliced into there lines if mounting to the frame by the tank? Idk if I should run all new rubber lines from top of the tank all the way to the filter on the engine or how I should do this...- stony7933
- Thread
- Replies: 30
- Forum: 6.9L IH & 7.3L IDI Diesels
-
Let’s make a deal - Sell me the website?
I know I've been searching through the site the last month or 2 before joining... Lots of great info. I think newbies like me start new posts, atleast my thought, because there is so much stuff changing.. like the e fuel pump question.. so many have went from quality units to junk in just a few...- stony7933
- Post #44
- Forum: Site comments and suggestions
-
New to the diesel world from Indiana
Picked up a 1990 ford f250 7.3l idi nonturbo truck with the zf5 5 SPD and 3.55 rear last fall. Truck has no bed but the rest of the truck was redone in 2009 and sat since. When I purchased it it didn't run so I get her running now...I got lots of questions and I see lots of info on here which is...- stony7933
- Thread
- Replies: 2
- Forum: Introduction
