Bought for
This was a kit for a 2001 Ford Excursion Powerstroke 7.3L , I belive its the same for the pick ups except the rear end is kicked out for fuel tank clearance on the X.
thanks
The Exhaust Company kept sending me wrong parts so this is what I have left over:
1-4" down pipe
1-axel Pipe Bent for an Excursion
1- T clamp
1-clamp
1-Straight Pipe 29 1/2"
this is almost a complete kit, you will need a muffler or a 3ft piece of 4" pipe and a Tip
the Kit was bought...
TRANNY SHOP
Went to the tranny shop and hooked her up to a scanner, pulled 2 codes:
FIPL out of range and torque converter slippage 3 to 4
The guy asked how much my truck was worth, I told him it was free but I had to drop a new engine in her.
He told me to Sell it as soon as possible...
tach
The tach is good never any issues. Reads good and steady.
The FIPL was replaced when the tranny was rebuilt, 40k ago.
The back bolt for me is a PAin to get because of the ATS turbo air clearer Box. The curve on the left side of the FIPL is almost at the top. and the right side is at...
SHOP
Going by the tranny shop in the am so they can read the codes, Dealer wanted $75 and leave it all day. Tranny shop said swing by any time takes 5 min. FREE.
Found the paper work and the tranny was rebuilt 40K ago, hopefully its a cheap fix.
thanks
Rod
FIPL
Got the multi meter and the low end is at 1.15 and wot is at 4.08.
Shifts a little better but still clunky and the OD light is still flashing.
Is there a reset for the OD light?
What do the numbers have to be at to get that neck snapping shifting, I want to avoid this, I want...
od light
"Is your OD light blinking? "
before reading this I never would of thought to look.
But the answer is YES it is blinking, and when trying to push nothing happens.
FIPL = MOTORCRAFT Part # CX1448
thanks
Rod
BANKS
Just got off the phone with banks, thay say you can hard wire the bypass with the orange and yellow wires. Maybe I can talk the old ladie into holding the wire in, while I drive down the road.
As the FIPL goes, Any directions for the Injection pump.
I am a 1 month old IDI owner so...
This truck has about 20k on a rebuilt tranny but when it shifts its a really bad clunk, sounds like it hurts.
Is this normal for the transcommand? If not what is the fix?
Could this of caused the flexplate problem in the old engine?
thanks
Rod
front shackle reversal, REAR Shackle Flip Kit
Looking at the sky-manufacturing site, they have a front shackle reversal kit and a rear Shackle Flip Kit.
The Front reversal kit adds 3 inches and the rear flip adds 4.5 inches.
anbody have any luck using these?
thanks
Rod
Just was out looking at the truck and figured it was time for new shocks.
Well I figured if I spend the money on just shocks for a truck with 160K miles why not throw new leaf spings all around too.
All the 4x4 I have ever owned I pulled off the sway bars, for those of you that have...
I am picking up the truck today and the old engine is sitting on a pallet if any one is in need of a core. I is a complete 7.3l idi from a 1993 f350 auto, The turbo is comming off. The engine ran awesome up till the flexplate broke and make that wonderfull sound.
I can send it back to the Co...
flexplate spacer
Got a call from Ford today an they said when the flexplate ripped apart it messed up the 1" spacer between it and the crank.
They then said Ford or international dont make it anymore so they would send it to a machine shop.
see how this works out
Rod
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.