Recent content by FordCummins
-
What is this for? (pic)
It's to remove the bolts that hold the flex plate to the torque convertor on the automatice. The smaller hole to the right of that (has a plastic plug) is the one used for the barring tool.- FordCummins
- Post #9
- Forum: 5.9L 12 valve Cummins
-
its alive (well sorta)
Anyone mess with the gov springs or the pump timing- FordCummins
- Post #6
- Forum: Diesel Conversion Forum
-
92 cummins
Bigger injectors and an after market fuel pin if that was not part of your "turned up the fuel pump".- FordCummins
- Post #2
- Forum: 1st Generation Cummins
-
Finally...I got one!!!
Congrats on your Cummins purchase. I suggest you buy a pyrometer and tweak on the pump for free. I agrre with rebel_horseman that the pipe going over the rear axle is smashed pretty good and would be nice to replace with 4" but it really depends on how much HP you want to add.- FordCummins
- Post #4
- Forum: 1st Generation Cummins
-
need some help again
CPS is used for Tach and alternator charging. As already mentioned - Check the Fuel Shutdown Solenoid. Improper adjustment will cause a no shutdown to cutting out if not opening all the way - - http://dodgeram.org/tech/dsl/troubleshooting/12v_fuel_solenoid.html- FordCummins
- Post #8
- Forum: 5.9L 12 valve Cummins
-
need help
Could be the Fuel Shutdown Solenoid which is normally closed so it must be getting weak, sticking or way out of adjustment. http://dodgeram.org/tech/dsl/troubleshooting/12v_fuel_solenoid.html- FordCummins
- Post #2
- Forum: 5.9L 12 valve Cummins
-
96 7.3 core engine for sale w/turbo
Injectors gone - Thank you- FordCummins
- Post #18
- Forum: Marketplace
-
WTB f350/250 cc 4x4 7.3l idi 86-92
Pulling the cab is not that bad of a job.- FordCummins
- Post #5
- Forum: Marketplace
-
96 7.3 core engine for sale w/turbo
Turbo parts pix Here is a shot of the turbo parts I dug up- FordCummins
- Post #17
- Forum: Marketplace
-
96 7.3 core engine for sale w/turbo
Parts dug up are, turbo, pedestal, EBPV, downpipe w/clamp, up pipes from exhaust manifolds, charge air tube with boots and clamps and intake tube with boot and clamp. Missing hardware list: 3 turbo mounting studs, 4 turbo mounting nuts, 3 EBPV mounting bolts, 1 up pipe mating bolt/nut and one...- FordCummins
- Post #16
- Forum: Marketplace
-
96 7.3 core engine for sale w/turbo
I think all the boots and clamps (plumbing) is there.. Are you wanting the pipes that run to the exhaust manifolds as well? It might be cheaper for you to pick it up rather then me shipping it. I work in Wilsonville (7am-3pm) if that helps.- FordCummins
- Post #14
- Forum: Marketplace
-
96 7.3 core engine for sale w/turbo
Sorry - I had almost given up on selling anything off this so have not been on the site. Yes I have HPOP for $150 plus shipping or make me an offer. Yes I have the Turbo $100 plus shipping. Greenbeast6.9 - If bad o-rings could cause over fueling in the cylinder then they could be bad. I...- FordCummins
- Post #11
- Forum: Marketplace
-
Dodge Auto '?'
I would give Source Automotive a call and ask for Robert 503-654-9004- FordCummins
- Post #2
- Forum: 1st Generation Cummins
-
-
96 7.3 core engine for sale w/turbo
I guess no one wants it whole so most internal parts are $10 each plus shipping. Turbo is $100. $200 for injectors. Heads, PS Pump, crank, cam, mainfolds are $50 each. Open to offers. Wiring and Transmission not 4-sale- FordCummins
- Post #6
- Forum: Marketplace
