Recent content by drewr13NJ

  1. drewr13NJ

    Interest in Electric Vacuum Pump Conversions?

    Following... Seems like a good idea, but I understand the liability issues. I've wanted to do a Cummins conversion on previous gas-powered trucks and thought this would be a good idea if I couldn't find a vacuum pump for the engine. Unfortunately, I have learned that most electric vacuum pumps...
  2. drewr13NJ

    72 Highboy swapped IDI on Deboss Garage

    Excellent Point. My IDI is a hard starter, but that 3126 HEUI engine cranks FOREVER! I understand he didn't want a heavy DT466 in there, but they are easier to rebuild and reasonably priced. I like Deboss Garage a lot and have been following the F-350 CAT build, but I was really disappointed...
  3. drewr13NJ

    Can I use Fuel Oil in a 6.9?

    Yes, off road fuel will run in these trucks. The front tank in my IDI was full of it when I bought it. It ran poorly on the front tank due to a rust pin hole on the pickup(sucking air), so it never was used up. It was a farm truck, so someone probably put farm fuel in it at some point. I...
  4. drewr13NJ

    Who's smarter?

    This is an interesting topic and there are many stand points/views to look at. I have owned several used cars and newer cars, had a couple car payments. I enjoy working on my IDI for the most part. I also enjoyed working on my old International pickups I had, but gas mileage was horrible. I...
  5. drewr13NJ

    Thoughts on Performance upgrades/direction/Cummins?

    Oh, figured I would ask you guys who have turbocharged and cranked up the pumps on these IDIS... Will my clutch hold? I have a SMF Fort Wayne Clutch and Driveline unit I installed when I rebuilt the engine 2 years ago. I agree that the little things nickel and dime ya on conversions.
  6. drewr13NJ

    Thoughts on Performance upgrades/direction/Cummins?

    Thanks for the replies. I was looking at VE pumped 12 valves for about $2 grand, but they seem to be bought up quick. That is also my understanding that 250hp is very doable with those rotary pumps. Typically the P-pump used engines are $3K up. I think Ill just use the 7.3 IDI, add the...
  7. drewr13NJ

    Thoughts on Performance upgrades/direction/Cummins?

    Hi everyone. Been lurking here for a couple years and posting occasionally, hopefully adding to the conversation. I have a dilemma and I wanted some opinions/thoughts. I'm thinking of doing a Cummins conversion on my 1992 in my signature. After doing research, looks like I'm going to be into...
  8. drewr13NJ

    what goes into pulling an idi?

    I have done it a couple ways. Both times with transmission separated, one time with hood off and other with hood on. IIRC, I never messed with the core support on either truck. I also pulled heads off the second engine before I pulled it out of the truck. Of course, it had the turbo off too...
  9. drewr13NJ

    How do you start your engine on WMO?

    I generally blend about 12 to 15% RUG to my WMO and I haven't had any issues. It is a little cold natured after sitting 8 to 10 hours at work in the cold weather, but it starts alright with the glow plugs and good batteries. It starts fine in the mornings with the block heater plugged in. In...
  10. drewr13NJ

    Actually retrieving WMO

    I have a Fill-Rite hand crank pump just like what Never-Have-I-Ether is looking at, and so far it has worked OK. I did have a problem once when I think the gasoline separated from my oil, and it was cold out. It seemed really hard to crank and it started to leak out of the seals (ie where...
  11. drewr13NJ

    New To WMO. Many questions. Any thoughts?

    This sounds like a good idea. If I run low on feedstock, I'll reach out to some of them. I work at a grain elevator and should be able to network with local farmers no problem!
  12. drewr13NJ

    Batteries,,,,

    This is what I tried and I love it! I had some bad air intrusion issues due to forgetting the O-ring on the fuel filter bowl. Without these batteries, I doubt it would have started. https://www.oilburners.net/threads/tech-101-lowering-battery-tray-for-obs-g31-batteries.81003/#post-1094304
  13. drewr13NJ

    Still possible to get a 6.9/7.3 4x4 for under $10k?

    Truck prices are crazy. I thought I got screwed two years ago. I bought a '92, the one in my signature for $6K, with a rusty snowplow. I drove it home from Cincinatti to Indy. PO put some money into it, fixed the brakes, new tires, etc, but it needed body work, front end work (steering...
  14. drewr13NJ

    New To WMO. Many questions. Any thoughts?

    I have ran used ATF from vehicles of my own in my generator and air compressor; both are IDIs and it runs well. I do have a tranny shop right down the street from me, but it is a chain, so they might be hesitant to sell/give it to me. Anyone buy WMO? I've seen some people want around a $1/gal...
Top